1) electrical wear ratio
电磨损率
1.
In this experiment,the results show that the electrical wear ratio of the tested Cu-Cr-Zr alloy increased obviously with the enhanced currents in the electrical wear course of the contact wire vs.
结果表明,在试验条件下,在合金接触线-黄铜粉末冶金滑块系统的电磨损过程中,Cu-Cr-Zr合金接触线的电磨损率随电流强度升高显著加强,由加载较小电流引起的磨损份额为0。
2) wear rate
磨损速率，磨损率
3) wear rate
磨损率
1.
Micro-wear test of soft materials(Ⅰ)——Wear scar measurement and wear rate calculation
软材料的微磨损测试研究(Ⅰ)——磨痕测量与磨损率计算
2.
The test study of roadheader cutting pick′s wear rate based on image process
基于图像处理的对掘进机截齿磨损率的研究
3.
The results showed that wear rate of CuNiMnFe alloy increases at the beginning stage and then decreases with increasing rotate speed and prolonging working time under no lubricant.
试验结果表明,干摩擦条件下CuNiMnFe合金的磨损率随着摩擦时间的增加而降低;随着转速的提高,呈先增加后降低的趋势。
4) wear ratio
磨损速率
1.
Meanwhile everage wear ratio was taken as wear criteria and the effect of the different laser engergy densitys on everage .
使用扫描电镜和X射线衍射仪对强化区组织进行了分析 ,并在销盘式摩擦试验机上对激光处理 9SiCr工具钢和热轧 2 0MnSiV钢配副进行了干摩擦和油润滑试验 ,同时以平均磨损速率作为磨损量的指标 ,研究不同激光能量密度对磨损量的影响并分析了其磨损机理。
5) wearing rate
磨损率
1.
This paper discusses the relation of the wearing rate to bed weight, air rate,wearing time by the wearing experiment of particle in fluidized bed.
通过流化床内颗粒磨损实验，探讨了磨损率随床重、气速及时间的变化关系，并对磨损前后物料粒径分布进行了对比，推断出颗粒的磨损机制。
6) wear rate
磨损速率
1.
The wear rate, ,for the surface oxidation of specimens first decreases then increses with an increase in test temperature.
在不同温度下 ,对 3种Fe基粉末冶金材料的冲击接触磨损速率进行了试验研究 。
2.
The correlation between coating weight loss and sliding distance, the influence of spray parameters and powder fabrication process on the abrasive wear rate of the coatings were studied based on the experimental results.
采用橡胶轮磨损实验机 ,对三种类型粉末制备的 HVOF Cr3 C2 - 2 5 % Ni Cr涂层进行了磨料磨损实验 ,研究了涂层的磨损特性和喷涂工艺条件、粉末制备工艺对涂层磨损速率的影响。
补充资料：轧辊磨损
轧辊磨损
roll wear
Zhagun mosun轧辊磨损(roll wear)车L棍在轧制力作用下将发生不同程度的磨损。轧辊磨损的机理很复杂，铸铁轧辊中的共晶碳化物倾向于疲劳磨损，基体则倾向于磨粒磨损;锻钢的冷轧工作辊和支承辊倾向于粘着磨损，高温下还伴有氧化磨损;冷却和润滑介质可能引起不同的化学磨损包括腐蚀磨损;无水冷的热轧辊还有受塑性支配的磨损机制。至今尚无综合评定轧辊抗磨性的统一指标，即使有些磨粒磨损试验数据也因组间偏差而达不到满意的统一性。鉴于轧辊硬度易于测量，并在一定条件下可以反映耐磨性，所以一般就用径向硬度曲线来近似地表述轧辊的耐磨指标。生产中习惯用轧辊每磨损lmm的轧制量或每修磨一次的轧制量来考核轧辊的质量。 (范坚祥)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条