1) roll-bonding
轧制复合
1.
The technology of roll-bonding was applied to prepare the foaming precursor in this paper.
将轧制复合工艺应用于发泡预制体的制备,研究了粉末致密化过程与面板/芯层的结合机制。
2.
Author studied the production technology of aluminum foam sandwich prepared by roll-bonding/powder metallurgy foaming process in this paper,and analyzed the effect of main technological conditions on foaming structure of sandwich layer,and optimum technological parameters were finally obtained.
研究了采用轧制复合-粉末冶金发泡法制备的泡沫铝夹心板的生产工艺,探讨了主要工艺条件对芯层泡沫结构的影响,得到了优化的工艺参数。
3.
The dynamic temperature field during roll-bonding combined with high-frequency alternating current heating has been numerically simulated by a simplified model.
通过数值模拟获得了高频加热-轧制复合过程中的动态温度场。
2) roll cladding
轧制复合
1.
The microstructure and properties of roll cladding sheet of high speed steel and Q235 steel;
高速钢-Q235钢轧制复合板的组织与性能
2.
The explosive welding,roll cladding and explosive welding+rolling are three main processes currently in the manufacture of the layer-metal composite plate.
爆炸焊接、轧制、爆炸 +轧制复合法是目前 3种主要的层状金属复合板的生产方法。
3.
The roll cladding processes for copper and aluminum sheet are studied systematically together with the technological conditions for achieving the highest cladding strengths in different processes.
本文系统地研究了铜铝复合板的轧制复合工艺以及不同工艺中可获得最佳复合强度的工艺条件。
3) roll bonding
轧制复合
1.
The Ag/Cu bimetallic strips were prepared by roll bonding at different temperatures.
通过轧制复合方法,在不同温度条件下制备了Ag/Cu双金属板,研究了剥离载荷作用下分离强度与复合温度的关系,测定了复合基体的硬度并观察了分离界面形貌。
2.
Roll bonding is one of the major and the most intellectual production method commonly used in the manufacture of metal laminates, however, the rolling process and diffusion annealing treatment impact bonding strength and interface.
轧制复合是极具潜力的大规模生产钢/铝复合板的制备加工方法,但其界面的结合强度受到复合轧制工艺和轧后扩散退火工艺的严重影响。
4) rolling clad
轧制复合
1.
The effect of annealing at low temperatures for long time and at high temperatures for short time on the formability and bonding strength of Cu/Al/Cu rolling clad sheet has been studied and the reason that the annealing strengthening did not appear in this process has also been discussed.
研究了低温长时间和高温短时两种退火工艺对铜/铝/铜轧制复合板的成型性能及界面结合强度的影响,讨论了退火强化现象没有出现的原因。
5) sandwich rolling
复合轧制
1.
A powder-A1 plate sandwich rolling processing is proposed for preparation of aluminum alloy foam sandwich with a metallurgy bonding interface.
通过粉末-铝板复合轧制方法制备出一种界面为冶金结合的泡沫铝夹芯板。
2.
The foam aluminum sandwich panels with metallurgy bonding interface are prepared by the sandwich rolling method,the two Al face-sheets are stacked and mixed powders with foam agent are put between them,which are sandwich rolled and a foaming precursor is obtained,then it is foamed in heating furnace.
采用复合轧制的方法,即将带有发泡剂的混合粉末置于两铝面板之间进行复合轧制使之成为预制发泡体,然后再在炉中发泡的方法,制备界面为冶金结合的泡沫铝夹芯板,通过摆锤冲击实验,研究界面为冶金结合的泡沫铝夹芯板与胶接夹芯板的冲击性能的区别。
6) Composite rolling
复合轧制
1.
surface processing+composite rolling+heat treatment were carried out.
进行了钢-铜、钢-铝冷轧复合实验,即表面处理+复合轧制+轧后热处理。
2.
By the experiment of rolling stop,on the basis of analying the law of the composite rolling deformation of the double metals,the article derives the theoretical formulation of calculation of layer thickness ratio on the composite material of the double metals,and the error is less than 5% according to the check by the results of actual test.
通过轧卡实验，在分析双金属复合轧制变形规律的基础上，推导出了双金属复合材料厚比计算的理论模型。
3.
The principle of layer thichness ratio is studied experimentally in the process of Al-steel composite rolling and the formulation of rolling force was established.
用实验方法研究了铝－钢双金属复合轧制时层厚比的变化规律。
补充资料：轧制节奏
轧制节奏
rolling cycle
zhazh一Jiezou轧制节奏(rolling。yele)轧制时相邻两根轧件进入(或轧出)同一轧机的时间间隔。在同样条件下，轧制节奏越短，轧机小时产童越高;反之，轧机小时产量越低。影响轧制节奏长短的因素是多方面的，不仅与工艺因素(如坯料长短、断面尺寸大小、道次多少、操作条件等)有直接联系，也与设备条件(如轧机布置形式、机架多少、速度高低以及电机能力大小等)密切相关。合理地分配轧制道次使各机组负荷均匀、提高操作水平、减少操作间隙时间、改变操作方式、实行文叉乳制、在设备允许条件下加大变形量、强化轧制过程等都可收到缩短轧制节奏的效果。在进行轧钢车间设计时轧制节奏可根据已定的工艺和设备条件以及产量要求设定，也可根据相同或相近的现场生产条件进行实际测定。 (衷康)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条