1) tension deviation
紧度偏差
1.
The "tension deviation" derived by actual condition was revealed and the design method of serrated shroud was discussed.
根据锯齿冠结构原理,导出了包含锯齿冠结构特性参数(λ、ψ、βu、Δβ)的关系式,即锯齿冠结构特性方程,并将其图解成锯齿冠结构特性曲线,直观、清晰地描述了各特性参数之间的关系和变化规律;揭示了由实际条件产生的"紧度偏差",论述了锯齿冠结构的设计方法。
2) skewness bias
偏斜度偏差
3) thickness deviation
厚度偏差
1.
The effect of thickness deviation on the reflection spectra and phase shift of VCSELs has been analysed using optical transfer matrix method.
采用光学传输矩阵方法分析了厚度偏差对VCSEL的反射谱和反射相移产生的影响。
2.
For researching thickness deviation of wide heavy plate caused by bilateral stiffness difference of plate mill,rolling force distribution is analyzed by using the principle of forces and torques equilibrium and the effects of the stiffness difference of plate mill on plate thickness deviation under a variety of roll length,plate width and rolling force is studied too.
针对由于轧机两侧刚度差异引起的宽厚板两侧厚度偏差,采用力平衡和力矩平衡原理,分析了轧辊承受载荷的分布情况,研究了宽厚板两侧厚度偏差与轧辊长度、板宽、轧制力和轧机两侧刚度差异之间的规律。
3.
For researching thickness deviation of wide heavy plate caused by bilateral stiffness difference of plate mill, rolling force distribution is analyzed by using the principle of forces and torques equilibrium and the effects of the stiffness difference of plate mill on plate thickness deviation under a varity of roll length, plate width and rolling force is studied too.
针对轧机两侧刚度差异引起的宽厚板两侧厚度偏差,采用力平衡和力矩平衡原理,分析轧辊承受载荷的分布情况,研究宽厚板两侧厚度偏差与轧辊长度、板宽、轧制力和轧机两侧刚度差异之间的规律。
4) taper tolerance
锥度偏差
1.
According to the requests of API connecting casing pole to connecting intensity and sealed capability,the paper analyzes the effect of taper tolerance of pipe external thread and coupling internal thread on using properties of casing pole.
根据API螺纹连接套管柱对连接强度和密封性能的要求,分析了管子外螺纹与接箍内螺纹的锥度偏差对套管柱使用性能的影响,提出锥度偏差应在API标准要求的基础上加以内控,将极限公差缩小至机械加工允许的范围内,是提高石油套管柱使用性能的有效途径。
5) angle deviation
角度偏差
1.
Through comparing the image of the sample with the stand- ard one,the angle deviation and position deviation was obtained.
通过对摄取到的实际套准标记图像和标准图像进行比较,输出其角度偏差值和位置偏差值,以此作为自动套准控制系统中时印刷机套准调节的依据,并对一种"米"形套准标记的识别和检测进行了分析。
2.
The model with angle deviation was detail discussed, correct model could be made by exactly angle measurement.
分析了基于球杆仪的数控机床误差补偿测试原理 ,讨论了由于角度偏差引起的误差 ,指出基于球杆仪误差补偿模型的缺陷 ,提出采用该种模型必须精确测量角度
3.
Through comparing the image of the sample with the stand- ard one,the angle deviation and position deviation was obtained.
通过对摄取到的实际套准标记图像和标准图像进行比较,输出其角度偏差值和位置偏差值,以此作为自动套准控制系统中对印刷机套准调节的依据,并对一种"(?)"形套准标记的识别和检测进行了分析。
6) Deviation of roundness
圆度偏差
补充资料：紧度
分子式：
CAS号：
性质：单位体积纸或纸板的重量，以g/cm3或kg/m3表示。紧度可由定量和厚度数值计算而得。紧度是纸与纸板的重要性质，它影响着几乎所有的机械、物理和电气性能。紧度决定于纤维种类、打浆程度、压榨和压光程度、纸浆半纤维素含量以及辅料用量等。
CAS号：
性质：单位体积纸或纸板的重量，以g/cm3或kg/m3表示。紧度可由定量和厚度数值计算而得。紧度是纸与纸板的重要性质，它影响着几乎所有的机械、物理和电气性能。紧度决定于纤维种类、打浆程度、压榨和压光程度、纸浆半纤维素含量以及辅料用量等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条