1) viscosity deviation
黏度偏差
1.
The influence ofcarboxylend group content,meltim purity contentand meltintrinsic viscosity deviation on the production of PET melt direct spinning were discussed.
研究了聚酯熔体直接纺中熔体端羧基含量、熔体含杂量及熔体特性黏度偏差对生产的影响,提出了可行的对策。
2) skewness bias
偏斜度偏差
3) thickness deviation
厚度偏差
1.
The effect of thickness deviation on the reflection spectra and phase shift of VCSELs has been analysed using optical transfer matrix method.
采用光学传输矩阵方法分析了厚度偏差对VCSEL的反射谱和反射相移产生的影响。
2.
For researching thickness deviation of wide heavy plate caused by bilateral stiffness difference of plate mill,rolling force distribution is analyzed by using the principle of forces and torques equilibrium and the effects of the stiffness difference of plate mill on plate thickness deviation under a variety of roll length,plate width and rolling force is studied too.
针对由于轧机两侧刚度差异引起的宽厚板两侧厚度偏差,采用力平衡和力矩平衡原理,分析了轧辊承受载荷的分布情况,研究了宽厚板两侧厚度偏差与轧辊长度、板宽、轧制力和轧机两侧刚度差异之间的规律。
3.
For researching thickness deviation of wide heavy plate caused by bilateral stiffness difference of plate mill, rolling force distribution is analyzed by using the principle of forces and torques equilibrium and the effects of the stiffness difference of plate mill on plate thickness deviation under a varity of roll length, plate width and rolling force is studied too.
针对轧机两侧刚度差异引起的宽厚板两侧厚度偏差,采用力平衡和力矩平衡原理,分析轧辊承受载荷的分布情况,研究宽厚板两侧厚度偏差与轧辊长度、板宽、轧制力和轧机两侧刚度差异之间的规律。
4) taper tolerance
锥度偏差
1.
According to the requests of API connecting casing pole to connecting intensity and sealed capability,the paper analyzes the effect of taper tolerance of pipe external thread and coupling internal thread on using properties of casing pole.
根据API螺纹连接套管柱对连接强度和密封性能的要求,分析了管子外螺纹与接箍内螺纹的锥度偏差对套管柱使用性能的影响,提出锥度偏差应在API标准要求的基础上加以内控,将极限公差缩小至机械加工允许的范围内,是提高石油套管柱使用性能的有效途径。
5) angle deviation
角度偏差
1.
Through comparing the image of the sample with the stand- ard one,the angle deviation and position deviation was obtained.
通过对摄取到的实际套准标记图像和标准图像进行比较,输出其角度偏差值和位置偏差值,以此作为自动套准控制系统中时印刷机套准调节的依据,并对一种"米"形套准标记的识别和检测进行了分析。
2.
The model with angle deviation was detail discussed, correct model could be made by exactly angle measurement.
分析了基于球杆仪的数控机床误差补偿测试原理 ,讨论了由于角度偏差引起的误差 ,指出基于球杆仪误差补偿模型的缺陷 ,提出采用该种模型必须精确测量角度
3.
Through comparing the image of the sample with the stand- ard one,the angle deviation and position deviation was obtained.
通过对摄取到的实际套准标记图像和标准图像进行比较,输出其角度偏差值和位置偏差值,以此作为自动套准控制系统中对印刷机套准调节的依据,并对一种"(?)"形套准标记的识别和检测进行了分析。
6) Deviation of roundness
圆度偏差
补充资料：逼近函数的偏差
逼近函数的偏差
deviation of an approxmating function
通近函数的偏差【山血位扣of ana即.油加tiI犯如‘丘.;yoo.e。。e np:6二:狱a沁川e‘中y。二明。。1 逼近函数g〔K和一个给定函数f任叨之间的距离p匆，f).在同一个类叨内可以考虑用不同度量p，譬如一致度量 p(g，f)一碧笃}g(x)一f(x)I，以及积分度量 /(。，，)一(i一(·)一，(·):“·)’‘’，p一和别的度量.至于逼近函数的类K则可以用代数多项式、三角多项式，还有f关于某个正交系的正交展开的部分和，这些部分和的线性平均，以及一些别的集之、
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条