1) SIMULINK software tool
SIMULINK软件工具
2) SIMULINK
SIMULINK软件
1.
Aiming at the characteristic of pulse submerged arc welding process with change wire=feed system, the simuloting model was developed by the software of MATLAB/SIMULINK which consists of the main circuit simulation model, arc load system simulation model and arc changing system simulation model.
针对变速送丝调节系统脉冲埋弧焊的特点,利用MATLAB/SIMULINK软件对其动态过程进行了研究,建立了主电路仿真模型、电弧负载系统仿真模型及弧长变化系统仿真模型,并在此基础上形成了系统的整体仿真模型。
2.
In order to improve the accuracy of the simulation,one nonlinear dynamic simulative model for biaxial gas turbine is proposed by using calculation method of variable specific heat,in which the variation of gas-oil ratio and discharge pressure were considered,based on Matlab/Simulink.
为了提高燃气轮机仿真的精度,采用变比热容的计算方法,并考虑了油气比和排压的变化,基于Matlab/Simulink软件建立了一种非线性的考虑容积惯性的双轴燃气轮机动态仿真模型。
3.
Numerical simulation of two kinds flow valves was studied with SIMULINK software.
提出了以G型π桥液阻网络作为先导控制网络的数字式流量阀,分析了基于半桥和π桥液阻网络的数字式流量阀动态特性,应用SIMULINK软件对2种类型的流量阀动态特性进行了仿真。
3) MATLAB/Simulink
MATLAB/Simulink软件
1.
Kinematics Simulation of Crank-pilot Bar Mechanism Based on the Software MATLAB/Simulink;
MATLAB/Simulink软件的曲柄导杆机构运动学仿真
2.
Based on the software called Matlab/Simulink,simulated block diagram is built and the influence of several important parameters to the system is analyzed.
对火箭增压系统及其关键减压器建立数学模型,利用Matlab/Simulink软件搭出仿真框图,分析几个重要参数对系统的影响,对相似弹箭体阀门系统的研究分析提供一种方法和思路,为解决增压系统动态不稳定问题进行了有益的探索。
3.
Based on space vector pulse width modulation for asychronous motor,the mathematical mode is established and simulinked in MATLAB/SIMULINK.
依据异步电动机矢量控制理论及电压空间矢量脉宽调制原理,介绍一种改进的空间矢量脉宽调制技术(SVPWM)异步电动机矢量控制系统的控制模式,利用MATLAB/SIMULINK软件建立控制系统的仿真模型,对该控制系统进行速度和负载转矩动态特性研究,给出控制系统动态仿真结果。
4) MATLAB/Simulink software
MATLAB/Simulink软件
1.
By using matlab/simulink software,the application of direct torque control(DTC)in per- manent magnet synchronous motor chives is discussed.
根据永磁同步电动机的数学模型,结合直接转矩控制理论,以空调用永磁同步电动机为例,利用Matlab/Simulink软件,对永磁同步电动机直接转矩控制仿真建模。
2.
Then the process which considers the metamorphic(t, s, S) strategy was dynamic and real-time simulated based on MATLAB/Simulink software, and provided the opportunity and quantity when the goods enter and exit the storage.
首先通过选择使库存总费用的日平均值最低的最优库存策略,建立了较复杂的变质的库存系统的仿真模型,然后基于MATLAB/Simulink软件动态实时模拟了变质的(t,s,S)策略下的库存系统的入库、出库时机和数量。
5) SIMULINK software package
SIMULINK软件包
1.
A dynamic simulation tool,SIMULINK software package in MATLAB,is taken as the development tool, and applied in the dynamic response computation of the hydraulic servo closed-loop control system.
以MATLAB中动态仿真工具SIMULINK软件包为开发工具,将其应用于该液压伺服闭环控制系统的动态响应计算中,针对上述两种闭环控制系统,给出了考虑干扰量情况下的SIMULINK仿真方法。
6) SIMULINK software
SIMULINK软件
1.
This article analyzes the application of the Matlab/Simulink software in simulation to the mechanical vibration system of two-freedom-degree by listing examples,it can not only simplify computer processing,but raise quality and reliability of computer processing,thus gains much better effect.
通过实例分析了Matlab/Simulink软件在二自由度机械振动系统仿真中的应用 ,不但大大地提高了编程的效率 ,而且提高了编程的质量和可靠性 ,取得了很好的效
2.
Later adopted the Simulink software to simulate this method.
随后采用了Simulink软件完成正交变换方法的仿真系统的设计,验证了该方法的可行性和有效性。
3.
In order to provide the real jamming environment for simulating the radar system and evaluating its anti-jamming performence, three typical models of active blanking jamming were established by using MATLAB/ Simulink software.
为开展干扰条件下雷达系统仿真及抗干扰性能评估提供较为真实的干扰信号,利用Matlab/Simulink软件,建立了3种典型有源压制性干扰模型。
补充资料：SI
有机硅树脂简称SI，是由三乙氧基硅烷等缩合而成。溶于乙醇、丁醇、醋酸乙酯、丙酮、苯、甲苯、环己酮等。预聚体在低温下能快速固化，固化后的树脂硬度高、耐热、耐磨、耐辐射、耐水、防潮、耐大气老化，低温(-50℃)不脆化。透明度高，可见光透光率90％以上。无毒。
用作酚醛树脂和环氧树脂剂的改性剂，可提高耐热性和耐水性贮存于阴凉、通风、干燥的库房内。
用作酚醛树脂和环氧树脂剂的改性剂，可提高耐热性和耐水性贮存于阴凉、通风、干燥的库房内。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条