1) NBR emulsoid
丁腈乳胶
1.
It is put forward in this paper that a new technologic method to prepare the winding clutch friction materials by using water-based phenolic resin modified by NBR emulsoid as adhesive , glass fiber , core-spun yarn as the reinforcing fibers and the two new NBR composite filler as the main filler.
本文提出了以丁腈乳胶改性水基酚醛树脂作粘合剂,分别以玻璃纤维和复合包芯纱纤维作为增强材料,采用两种新型丁腈复合填料作主要填料制备高性能离合器摩擦材料的试验方法。
2.
It is proposed in this paper that a new technological method to prepare the winding clutch friction materials by using water-based phenolic resin modified by NBR emulsoid as adhesive,glass fiber,core-spun yarn as the reinforcing fibers and the two new NBR composite filler as the main filler.
本文提出采用丁腈乳胶改性酚醛树脂作粘结剂、采用玻璃纤维和复合包芯纱作为增强纤维、丁腈橡胶复合填料制备离合器摩擦材料的工艺方法。
2) butadiene-acrylonitrile latex
丁腈胶乳
1.
Study on butadiene-acrylonitrile latex wastewater treatment by activated carbon-microwave irradiation;
活性炭-微波辐照处理丁腈胶乳生产废水的研究
3) carboxylated acrylonitrile-butadiene rubber latex
羧基丁腈胶乳
4) carboxylic acrylonitrile butadiene rubber latex
羧基丁腈胶乳(XNBRL)
5) XNBRL
浸渍用羧基丁腈胶乳
1.
This article discusses the method for the minimum formation temperature(MFT) test of carboxylated NBR latex(XNBRL),experiments its super filming performance compared with other latex shch as EBR,SBR and NBR,explains the connection between filming properties and production process of XNBRL.
以浸渍用羧基丁腈胶乳为例论述了最低成膜温度的测定方法及其在成膜过程中随环境温度而发生的变化 ,并与其它类型胶乳相对比 ,试验证实了羧基丁腈胶乳所特有的优良成膜性。
6) carboxyl-acrylnitrile latex
羧基丁腈合成胶乳
补充资料：丁腈
偶氮二异丁腈也有称丁腈，简称AIBN．分子量164．21，白色柱状结晶或白色粉末状结晶，熔点102～104℃。溶于甲醇、乙醇、乙醚、丙酮、石油醚和苯胺等有机溶剂。遇热分解放出氮气和含-(CH2)2-C-CN基有机氰化物。分解温度64℃。室温下缓慢分解，100 ℃急剧分解．能引起爆炸着火，易燃。有毒。放出的氮气和有机氰化物对人体危害较大。
用作醋酸乙烯和丙烯酸酯等聚合或共聚合的引发剂。也可用作发泡剂。
贮存于干燥、通风、避光和温度10℃以下的库房内，因为室温下缓慢分解，在30℃贮存数月显著变质。远离火种、热源。
用作醋酸乙烯和丙烯酸酯等聚合或共聚合的引发剂。也可用作发泡剂。
贮存于干燥、通风、避光和温度10℃以下的库房内，因为室温下缓慢分解，在30℃贮存数月显著变质。远离火种、热源。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条