2) high strength angle steel
高强角钢
1.
Experiment on bearing capacity of 48 Q460 high strength angle steel for compression members attached by one leg was carried out,the results of mechanical behavior and deformation for specimens were analyzed.
通过对48根Q460高强角钢单边连接压杆承载力试验,对其受力性能和变形进行研究。
2.
Aiming to this design,structural calculation and economic analysis are performed in two aspects,including high strength angle steel and steel tube members.
针对该方案,分别从高强角钢及钢管构件两大方面进行了结构计算及经济性分析,并建议:750kV同塔双回紧凑型杆塔采用高强钢,单回紧凑型杆塔是否采用高强钢则需依据综合经济性而定;750kV同塔双回紧凑型杆塔主材采用Q345钢管构件,但单回紧凑型杆塔不建议采用;上述2种杆塔采用Q420钢管构件的经济性更为显著,但还需深入开展构件及节点构造等方面的试验研究。
3) high strength steel
高强度钢
1.
Development on control of hydrogen in high strength steel weld metal;
高强度钢焊缝金属氢控制研究进展
2.
Analysis about formation and microstructure of laser-welding-tailored-blanks with unequal thickness of high strength steels;
高强度钢差厚板激光拼焊焊缝成形及组织分析
3.
Precipitate Behavior of Second Phase and Structure of Annealed 1.5mm Cold Rolling Sheet of Nb-Ti Microalloy High Strength Steel;
Nb-Ti微合金高强度钢1.5mm冷轧板退火组织和第二相析出行为
4) high-strength steel
高强度钢
1.
Research of accelerated corrosion test method of zinc, cadmium plating on high-strength steel;
高强度钢锌、镉镀层加速腐蚀试验方法研究
2.
The trial qualification by us ing less-matched welding materials to weld high-strength steel;
焊接高强度钢用低匹配焊接材料的试验评定
3.
Effect of processing parameters on strength and toughness of high-strength steel
工艺参数对高强度钢强度及韧性的影响
5) high strength IF steel
高强度IF钢
1.
The relationship of galvannealed temperature,galvannealed time,surface pattern,η,ζ,and δ1 were investigated by testing high strength IF steel with the intensity of 340 MPa.
选取340 MPa高强度IF钢热镀锌钢板作为实验原板,分析了不同镀层退火工艺参数对板带镀层表面的影响,重点研究了镀层退火的温度、保温时间与表面形貌以及η,ζ,1δ各个相的关系。
2.
This paper summarizes research and application of galvanizing on ultra light auto body steel,stressing on galvanizing process and factors affecting properties for bake-hardening steel,high strength IF steel,dual phase steel and transformation induced plasticity steel.
综述了超轻汽车车体用钢热镀锌的研究及应用现状,重点介绍了烘烤硬化钢、高强度IF钢、双相钢、相变诱导塑性钢等热镀锌的生产工艺和性能影响因素。
3.
Compared with traditional high strength IF steel,the recrystallization behavior during annealing process of a high C-Nb high strength IF steel was studied by using a Gleeble-1500 simulator.
以传统高强度IF钢为对比,用Gleeble-1500热模拟机研究了440MPa级高C-高NbIF钢的再结晶行为,采用盐浴退火方法研究了退火温度对该钢显微组织和力学性能的影响。
补充资料：高强
（武艺）高超。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条