1) thermal superposition model
![点击朗读](/dictall/images/read.gif)
热叠加模型
1.
The average temperature of chips in stacked 3D-MCM was chosen as the evaluation target based on thermal superposition model and equation of heat conduction,and the fitness function for thermal placement optimization was determined.
基于热叠加模型并结合热传导公式,选取芯片的温度作为评价指标,确定出用于3D-MCM热布局优化的适应度函数,采用遗传算法对芯片热布局进行优化,得出了最优芯片热布局方案,总结出了可用于指导叠层3D-MCM芯片热布局设计的热布局规则;采用有限元仿真方法,对所得的热布局优化结果进行验证,结果表明热布局优化结果与仿真实验结果一致,本文所提出的基于热叠加模型的MCM热布局优化算法可实现叠层3D-MCM芯片的热布局优化。
2) superposition model
![点击朗读](/dictall/images/read.gif)
叠加模型
1.
The application of gray system and the periodical error superposition model in the recognition of seismic anomaly;
灰色与周期残差叠加模型在地震前兆异常识别中的应用
2.
On the influence of the ρ coefficient in superposition model on the calculation of the g factors of ground state
叠加模型中ρ系数对基态g因子计算结果的影响
3.
The local structure and EPR spectra of [VO(H_2O)_5]~(2+) in(NH_4)_2C_4H_4O_6 single crystal are interpreted simultaneously based on superposition model and two-spin-orbit-coupling parameter model.
采用叠加模型和双旋-轨耦合参量模型,建立了结构参数与EPR参量之间的定量关系;较好地解释了[VO(H2O)5]2+络离子的局域结构和EPR参量;研究结果发现,(NH4)2C4H4O6:VO2+晶体中络离子[VO(H2O)5]2+的键长为R//≈0。
3) superposed model
![点击朗读](/dictall/images/read.gif)
叠加模型
1.
A superposed model is proposed to simulate the f.
![点击朗读](/dictall/images/read.gif)
同时提出了绝缘子闪络后线路电压计算的叠加模型,并据此用贝杰龙法计算了闪络前后各相线路各点的对地电压。
2.
Therefore, in this pape we discuss the grey properties of groundwater system, give a superposed model of grey and cyclic error, and forecast the dynamics of the groundwater system by the model.
本文建立了灰色与周期残差叠加模型,并运用模型预测了地下水的变化动态。
4) model superp osition
![点击朗读](/dictall/images/read.gif)
模型叠加
5) heating model
![点击朗读](/dictall/images/read.gif)
加热模型
6) mixed hydrothermal superposition type
![点击朗读](/dictall/images/read.gif)
混合热液叠加型
补充资料:AutoCad 教你绘制三爪卡盘模型,借用四视图来建模型
小弟写教程纯粹表达的是建模思路,供初学者参考.任何物体的建摸都需要思路,只有思路多,模型也就水到渠成.ok废话就不说了.建议使用1024X768分辨率
开始
先看下最终效果
第一步,如图所示将窗口分为四个视图
第二步,依次选择每个窗口,在分别输入各自己的视图
第三步,建立ucs重新建立世界坐标体系,捕捉三点来确定各自的ucs如图
第四步,初步大致建立基本模型.可以在主视图建立两个不同的圆,在用ext拉升,在用差集运算.如图:
第五步:关键一步,在此的我思路是.先画出卡爪的基本投影,在把他进行面域,在进行拉升高度分别是10,20,30曾t形状.如图:
第六步:画出螺栓的初步形状.如图
第七步:利用ext拉升圆,在拉升内六边形.注意拉升六边行时方向与拉升圆的方向是相反的.
之后在利用差集运算
第八步:将所得内螺栓模型分别复制到卡爪上,在利用三个视图调到与卡爪的中心对称.效果如图红色的是螺栓,最后是差集
第九步:阵列
第10步.模型就完成了
来一张利用矢量处理的图片
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条