2) hot-press sintering
热压烧结
1.
Research on hot-press sintering process of N type thermoelectric materials ZnO;
N型热电材料ZnO热压烧结工艺研究
2.
Si_3N_4 ceramics were prepared by aligning theα-Si_3N_4 whisker in the substrate via tape casting and hot-press sintering.
利用流延成型使α-Si_3N_4晶须在基体中定向排列,并采用热压烧结技术制备了Si_3N_4陶瓷。
3.
Ti_3Al/TiC+ZrO_2 composites were prepared by mechanical alloying and hot-press sintering.
采用机械合金化和热压烧结制备了Ti3Al/TiC+ZrO2复合材料。
3) hot pressing sintering
热压烧结
1.
Beside the raw materials and formulation,the quality of diamond segments depend on the hot pressing sintering techniques and the quality of graphite mould.
人造金刚石锯片的刀头是采用粉末冶金工艺来制作的,其刀头的质量性能除了取决于原材料的选择与配比,还取决于热压烧结工艺以及石墨模具的性能。
2.
Silicon carbide particles/copper (SiCr/Cu) composites were prepared by hot pressing sintering with electric resistance heating.
用电阻热压烧结法制备了碳化硅颗粒/铜(SiC_p/Cu)复合材料。
3.
LaB_(6)ZrB_(2) composite powders with different content of ZrB_(2) were synthesized by carbon thermo-reduction method and the corresponding polycrystalline composites were fabricated by hot pressing sintering method.
通过热压烧结法制备了相应的复合材料,其性能测试结果表明:随着ZrB2含量的增加,LaB6ZrB2复合材料的硬度和弯曲强度均随之增大,而断裂韧性则先增后减,在ZrB2质量分数为21%时,其断裂韧性达最大值。
4) hot pressing
热压烧结
1.
TiB2 cermet containing 7wt% Fe and 3wt% Mo was fabricated by hot pressing.
实验结果表明,随着热压烧结温度升 高,材料抗弯强度、洛氏硬度出现峰值,热压烧结时间延长,抗弯强度有所下降。
2.
The effects of different doses of the raw materials in ZrO_2-B_4C-C towards the calcined and sintered products were investigated by hot pressing.
采用固相反应和热压烧结方法研究了ZrO2B4CC体系反应原料的不同掺量对产物相组成的影响规律,并对烧结体进行了物相分析、粒度分析、显微结构分析、相对密度和化学分析。
3.
SiC/SiC composites were prepared by hot pressing using nano-SiC and sub-micrometer SiC powders for matrix formation.
采用纳米SiC和亚微米SiC粉料作为基体形成原料,通过热压烧结技术制备了SiC/SiC 复合材料。
5) hydrothermal crystallization
水热结晶
1.
Nanotubes of gadolinium carbonate hydrate were prepared through a simple hydrothermal crystallization method with commercial carbonate as precursor for the purpose of enriching rare earth products and enhancement of their applications.
为丰富稀土产品 ,拓展稀土应用领域 ,以现有稀土产品之一的碳酸钆为原料 ,通过水热结晶 ,直接合成水合碳酸钆薄壁纳米管 ,用粉末X射线衍射、热分析、透射电镜技术表征了样品的结构、形貌和热稳定性 水合碳酸钆纳米管长为数百纳米至 1 5 μm ,管径为 5 0～ 2 0 0nm ,在 6 80℃以上分解后可得体心立方晶系的氧化钆纳米管 ,尺寸和形貌未发生显著变化 该法条件温和 ,流程短 ,可作为现有湿法冶金工艺的一个部分 ,直接生产碳酸钆和氧化钆纳米管 ,而且克服了立方相氧化物不易可控生长的缺
2.
H2O2 oblation-hydrothermal crystallization combined method was employed for the first time for the preparation of pure MoO3 powder.
首次使用过氧化氢氧化－水热结晶联合法制备了高纯ＭＯＯ３粉末。
6) hot-pressing sintering
热压烧结
1.
Pressureless and hot-pressing sintering of Ce-TZP/Al_2O_3 composite ceramics;
无压及热压烧结法制备Ce-TZP/Al_2O_3复相陶瓷材料
2.
Preparation of oriented plate-like WC grains in cemented carbides by high-energy ball milling and special hot-pressing sintering;
高能球磨热压烧结制备定向排布板状WC硬质合金
3.
In-situ reaction hot-pressing sintering process of SiC/MoSi_2 composites
SiC/MoSi_2复合材料的原位反应热压烧结工艺
补充资料：热结
热结
热邪结聚于里的病理变化。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条