1) twice sintering process
二次烧结工艺
2) double-firing process
二次烧成工艺
3) sintering process
烧结工艺
1.
Influence of sintering process on the cutting and welding performance of diamond saw blade;
烧结工艺对金刚石锯片切割性能和焊接性能的影响
2.
Research on hot-press sintering process of N type thermoelectric materials ZnO;
N型热电材料ZnO热压烧结工艺研究
3.
Study on sintering process of P/M M42 high speed steel prepared by spark plasma sintering
SPS烧结M42粉末高速钢的烧结工艺研究
4) sintering technology
烧结工艺
1.
Study on the sintering character of iron ore and the optimization of sintering technology;
唐钢铁矿石烧结性能研究及烧结工艺优化
2.
Research on the sintering technology of the PZT piezoelectric ceramic filter;
PZT压电陶瓷滤波器的烧结工艺研究
3.
The sintering technology,mechanical properties and microstructures of Mo5Si3/MoSi2 with and without La2O3 were investigated.
通过粉末冶金方法制备了Mo5Si3/MoSi2和La2O3/Mo5Si3/MoSi2复合材料,探讨了其烧结工艺。
5) sintering
['sintəriŋ]
烧结工艺
1.
Study on Cathode Sintering Technology in the Process of Electrochemical Reduction of TiO_2;
电化学还原法制备金属钛的阴极烧结工艺研究
2.
The investigation of the sintering process of Al-10Mg binary alloy system was carried out ly use of high-temperature optical microscope,the effects of pressure and heating mode on behavior of binary alloy during sintering were studied.
为改进常规烧结工艺提供了直接的试验依据。
3.
The sintering processes and their effects of sintering processes on microstructure, density and compressive property of the alloy sintered were investigated.
0Cr(%)气雾化预合金粉末为原料,采用注射成形工艺制备了TiAl合金材料,研究了TiAl合金烧结工艺以及烧结工艺对烧结体显微组织、密度和性能的影响。
6) sintering technique
烧结工艺
1.
Study on sintering technique of NiFe_2O_4/SiC_w used as matrix of inert anodes;
SiC晶须增强NiFe_2O_4基惰性阳极材料烧结工艺研究
2.
Strontium barium niobate/barium strontium titanate(BSTN in short) was prepared through a modified sol-gel technique,by controlling the ratios of different components in the sol solution to suspend the fine strontium barium niobate powders(SBN in short)which was made beforehand by traditional ceramic sintering technique.
本文以钛酸四丁酯等配制溶胶前驱体溶液,通过控制前驱体溶液中各组分的配比成功制备了粘稠的溶胶溶液,以悬浮传统固相烧结工艺制备的微米级铌酸锶钡陶瓷粉体,在超声分散等的作用下形成均匀凝胶,最后成功制备出复相陶瓷坯体。
3.
In this paper, the influence of different sintering technique on mechanical properties and microstructure of CNTs/HAp composite was studied.
本文主要研究了不同烧结工艺对碳纳米管 /羟基磷灰石复合材料力学性能与微观结构的影响。
补充资料：二次烧成
分子式：
CAS号：
性质：陶瓷体在施釉前后各进行一次高温热处理的烧成方法。基本上有两类情况，其一是未上釉的生坯先烧一次成素坯，施釉后再烧一次。这种二次烧成工艺多用于生坯强度较低的陶瓷制品，如部分釉面砖及精陶制品等。某些工业陶瓷坯中加入较多有机增塑剂、黏结剂、分散剂等，也常采取先素烧、施釉、再烧成的方法。其二是某些半导体陶瓷，如晶界层电容器等常先采用还原气氛(如通氢或氢和氮)烧成，再涂覆晶界绝缘层膏后进行第二次烧成(氧气氛)，使半导化晶粒之间形成晶界绝缘层。通常二次烧成对保证产品质量、提高合格率有利，但产品能耗有所增加。
CAS号：
性质：陶瓷体在施釉前后各进行一次高温热处理的烧成方法。基本上有两类情况，其一是未上釉的生坯先烧一次成素坯，施釉后再烧一次。这种二次烧成工艺多用于生坯强度较低的陶瓷制品，如部分釉面砖及精陶制品等。某些工业陶瓷坯中加入较多有机增塑剂、黏结剂、分散剂等，也常采取先素烧、施釉、再烧成的方法。其二是某些半导体陶瓷，如晶界层电容器等常先采用还原气氛(如通氢或氢和氮)烧成，再涂覆晶界绝缘层膏后进行第二次烧成(氧气氛)，使半导化晶粒之间形成晶界绝缘层。通常二次烧成对保证产品质量、提高合格率有利，但产品能耗有所增加。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条