1) pellet sintering process
球团烧结工艺
2) pellet sintering
球团烧结
1.
The results show that the pellet sintering technique for Yamansu′s net iron concentrate has obvious advantages over concentional sintering processes.
研究了全精矿球团烧结中焦粉内配比例、焦粉粒度、烧结矿碱度的选取，并进行了配加生矿粉试验，试验结果表明，雅满苏铁精矿全精矿球团烧结工艺明显优于普通烧结工艺。
2.
So by comparing with conventional sintering, chromite pellet sintering technology (PST) and its agglomeration mechanism have been studied.
通过查阅国内外大量文献，在对不同铬铁矿造块方法进行综合分析对比的基础上，开展了铬铁矿球团烧结工艺及机理研究。
3.
Iiuquan Iron and Steel Company) had developed a new acid pellet sintering process, but there are still some problems to be dissolved, such as poor gas permeability and higher rate of fine material in product.
本文针对酸性球团烧结新工艺工业生产中存在着烧结过程透气性差、成品烧结矿细粒级含量高的问题，通过对酸性球团烧结工艺原始料层透气性和普通烧结工艺原始料层透气性、酸性球团烧结工艺实际生产过程中料层温度变化和负压变化等的测定及对添加白云石、钒钛矿、萤石的酸性球团烧结矿矿相分析及粘结相粘度测试、配加白云石、钒钛矿工业生产试验、外滚生石灰改善酸性球团烧结过程透气性等试验，探讨了解决问题的途径。
3) pelletized sintering
球团烧结
1.
In this paper, some technological parameters of pelletized sintering are studied experimentally and discussed theoretically,and the optimum parameters are given out.
本文就铁精矿球团烧结的部分工艺参数进行了试验研究和理论探讨，指出了球团烧结的部分最佳工艺参数。
4) pellets sintering
球团烧结
1.
Application Study of Intelligent Control Method on Pellets Sintering Process;
球团烧结过程智能控制方法及其应用研究
2.
Aimed at the complexity of controled project,the uncertainty of the mathematical modal and the high requirements of control quality during the pellets sintering grate process,an intelligent optimization control method based on the permeability soft sensing model was proposed in order to improve the automation control level in pellets sintering process.
针对球团烧结链篦机过程被控对象复杂、数学模型不确定以及控制要求高等特点,提出一种基于球团烧结透气性软测量模型的专家控制方法,以提高球团烧结过程自动化控制水平,最终实现了球团烧结生产过程链篦机子系统的优化管理,优化控制和优化运行。
6) MPS process
小球团烧结
1.
Point at the problems presented in MPS process, the uniform sintering technology was applied to perfect the MPS process in SHUIYE I & S Co As a result, the quality and quantity of sinter were increased and the fuel consumption was decrease
针对安钢集团水冶钢铁有限公司小球团烧结生产中存在的问题 ,采用均质烧结技术对其进行完善 ,取得了产质量提高 ,燃耗降低的良好效
2.
The output increased and coke saving of blast furnace was achieved by using MPS process.
三钢烧结厂在原烧结混合料准备系统上增加8个造球盘及配套设施,形成了小球团烧结生产的新工艺。
3.
The technical modifications with MPS process and many patents were presented in this paper As a result,the granulation ratio of mix was increased greatly ,the bed depth was increaed from 300mm to 550～ 600?mm and the solid fuel consumption was decreased obviousl
介绍了济钢烧结在技改过程中 ,采用小球团烧结技术及多项专利的情况。
补充资料：烧结、球团成品率
烧结、球团成品率
yield of finished product of sintering and pelletizing
shaoj浦e qiutuan ehengPinl。烧结、球团成品率(yield。f finished produetof sinteringand pelletizing)烧结成品率为干烧结料〔其中包括返矿)的成品烧结矿产出率;球团成品率为干球团料(其中包括返矿)的成品球团矿产出率。用公式表示为p一(Q。/Q:)x10o%。尸为烧结料或球团料的成品率，%;Q:为成品烧结矿或球团矿的数量，t;Q:为干烧结料或干球团料的数量，t。 烧结料和球团料的成品率，实为二者的收得率。在铁矿石造块工艺操作稳定的条件下，返矿量基本不变，P值大小仅与烧结料或球团料的烧损量有关，配人烧损量大的物料多，p值小;反之，尸值大。因此，造块配料的矿石种类、燃料和熔荆的数量，对尸值都有直接影响。在原料条件和造块成分确定之后，烧损量变化不大，尸值取决于造块工艺操作水平，凡能提高烧结矿和球团矿强度和降低返矿量的操作，都将使QZ增加，Ql减少，结果尸值升高。提高烧结料和球团料的成品率，是提高二者生产率和降低能耗的重要途径之一。此外，还可以用尸值变化情况检验操作制度的合理性。 除烧结料成品率外，还有烧结矿成品率的指标，即单位质量烧结饼(即全部烧结残存物)中成品烧结矿的数量。它同烧结矿强度直接有关。 (朱家骥)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条