1) corrosion and abrasion
腐蚀与磨损
1.
When artificial prosthesis were implanted into human body, particles generated by reaction of corrosion and abrasion in human body environment were usually less than 10μm, which belonged to the scope of micro-abrasive wear.
人工假体植入人体后,在人体内环境下受到腐蚀与磨损的作用,磨损所产生的颗粒小于10μm,属于微磨粒磨损的范畴。
2) corrosive wear
腐蚀磨损
1.
Effect of aging treatment on corrosive wear characteristics of σ strengthening austenite stainless steel;
时效处理对σ相强化奥氏体不锈钢腐蚀磨损特性的影响
2.
Environmental embrittlement of materials in corrosive wear;
腐蚀磨损过程中材料的环境脆性
3.
Investigation on corrosive wear property of nano-Al_2O_3 particles reinforced Ni-based alloying layer
纳米Al_2O_3颗粒增强Ni基复合镀渗合金层的腐蚀磨损性能研究
3) corrosion-wear
腐蚀磨损
1.
A new corrosion-wear resistant alloy for pumps used in hydrometallurgy of zinc and it's heat treatment were studied.
设计了用于湿法炼锌介质环境的新型耐腐蚀磨损合金的化学成分和热处理工艺,通过金相显微镜、电子探针、扫描电镜、腐蚀磨损试验等方法,分析了新型合金的显微组织、磨损形貌,研究了它与对比钢CD-4MCu、常用叶轮材料YL的腐蚀磨损性能。
2.
The characteristics of corrosion-wear of 13Cr-24Mn-0.
44N不锈钢在体液润滑条件下具有良好的抗腐蚀磨损能力,单位时间的磨损量仅为水润滑条件下的25%左右,摩擦因数下降了近30%。
3.
The microstructure,corrosion resistance in acidmedia as well as corrosion-wear behaviors under different impact velocities or in acid media with various densities were investigated for the all laser remelted alloy coatings.
研究了在４５钢表面进行激光熔敷镍基合金、镍基Ｃｒ２Ｏ３合金和镍基ＷＣ合金的熔敷层的组织结构、耐蚀性及不同冲击速度和不同浓度的腐蚀介质下的腐蚀磨损特性。
4) Corrosion-erosion
腐蚀磨损
1.
Corrosion-erosion Resistance of High Chromium Cast Iron Cr28 in Wet Parts of Slurry Pump in Alumina Ore;
氧化铝矿用渣浆泵过流件高铬铸铁Cr28的腐蚀磨损性能
2.
Microstructure and Corrosion-erosion Resistance of Directionally Solidified High Cr Cast Iron;
定向凝固高铬铸铁Cr28的组织和腐蚀磨损性能
3.
The parts of slurry pump which carbides plumbwith working face, is got by using the technology in directional solidification,it make resistance to corrosion-erosion heighten.
分析了材料失重过程中腐蚀磨损的交互作用。
5) wear-corrosion
腐蚀磨损
1.
The wear-corrosion behavior of 316L stainless steel,which is one of the most frequently used biomedical materials for artificial joints,was studied in distilled water and Hank′s solution.
对人工关节常用的生物医用材料 316L不锈钢在蒸馏水和Hank′s模拟体液条件下的腐蚀磨损行为进行了研究,通过改变载荷和磨损时间考察了不同因素对其腐蚀磨损的影响规律。
2.
The Corrosive wear properties of Ni60 +20%WC alloy coatings by laser cladded process have been measured and wear-corrosion surface morphologies in diffirent impact velocities and sulphuric-acid concentrations have been studied by SEM.
测定了Ni60＋20％WC合金激光熔敷层的腐蚀磨损性能，用扫描电镜研究了冲击速度和介质浓度对腐蚀磨损表面形貌的影响。
3.
In this paper,the progress in wear-corrosion research in apparatus,influencing factors and use of surface modifaction to enhance wear-corrosion resistance is summarized,and the development trends in this field are also pointed out.
综述了最近几年来,腐蚀磨损的测试设备、影响因素以及利用表面改性提高腐蚀磨损性能方面的研究进展状况,并指出未来研究腐蚀磨损主要工作方向。
6) corrosion wear
腐蚀磨损
1.
The corrosion wear behavior of titanium alloy TC11 flat was investigated in artificial sea water and distilled water by using ball-on-flat configuration with 5 mm reciprocating amplitude.
采用球-面接触方式,在振幅为5 mm条件下研究了TC11钛合金在人造海水和纯净水中的往复滑动腐蚀磨损行为,采用扫描电子显微镜观察磨屑和磨痕表面形貌,用能谱仪测试微区元素分布,用非接触式表面形貌仪测定磨痕的三维表面形貌及其磨损体积损失,研究了载荷、滑动频率以及介质对TC11钛合金摩擦系数和磨损量的影响,并用动电位扫描法分析TC11在腐蚀磨损前后的电化学行为。
2.
The effect of Si content on the corrosion wear resistance of low chromium white cast iron in the slurry with Cu2+ ion was studied by three-body corrosion wear test.
采用三体腐蚀磨损试验方法研究了硅对低铬白口铸铁在含铜离子浆料介质中的腐蚀磨损耐磨性的影响。
3.
The corrosion wear characteristics of three kinds of stainless steels were investigated by using self-made corrosion-wear tester in the condition of different solid/liquid ratio; concentration of sulfuric acid and erode speed.
利用自行设计的腐蚀磨损试验装置研究了三种不锈钢在不同固液比、硫酸浓度和线速度的条件下的耐腐蚀磨损性能;结果表明,在低硫酸浓度、高固液比和高线速度的条件下,沉淀硬化马氏体不锈钢具有良好的耐腐蚀磨损性能;而在腐蚀性较强、线速度较大的条件下,双相不锈钢的耐腐蚀磨损性能优于沉淀硬化马氏体不锈钢和奥氏体不锈钢;第二相强化奥氏体不锈钢在腐蚀性较强、耐磨性较弱的环境中耐腐蚀磨损性能较好。
补充资料：腐蚀
分子式：
CAS号：
性质： 材料与它所处的环境发生作用而产生的损坏。不仅金属材料会因腐蚀而损坏，而且非金属材料(如塑料、混凝土及木材等)也会因发生腐蚀而损坏。但在工业上，金属及其合金至今仍然是最主要的结构材料。金属因腐蚀造成的直接损失是巨大的，估计全世界每年约有相当于年产量10％的钢铁由于腐蚀而报废。腐蚀通常是指金属的损坏。
CAS号：
性质： 材料与它所处的环境发生作用而产生的损坏。不仅金属材料会因腐蚀而损坏，而且非金属材料(如塑料、混凝土及木材等)也会因发生腐蚀而损坏。但在工业上，金属及其合金至今仍然是最主要的结构材料。金属因腐蚀造成的直接损失是巨大的，估计全世界每年约有相当于年产量10％的钢铁由于腐蚀而报废。腐蚀通常是指金属的损坏。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条