1) sintered brick production
烧结砖生产
1.
In view of this situation, this paper applied an important environmental management tool——life cycle assessment methods (Life Cycle Assessment, LCA) to carry out environmental impact assessment for common sintered brick, which account for approximately 70% of sintered brick production in the country.
针对这一现状,本文利用生命周期评价方法(Life Cycle Assessment,LCA),对占我国烧结砖产量70%的普通烧结砖生产进行环境负荷分析。
2) Sintering
['sintəriŋ]
烧结生产
1.
This paper mainly analyzes the impacts of the fluctuation of return fines quality and quantity on sintering,putting forth countermeasures of controlling best return fines quantity through reducing water and carbon fluctuations and increasing surface-layer sintered ore strength.
主要分析了返矿质量和数量的波动对烧结生产的影响,提出了通过减少水、碳波动,提高表层烧结矿强度等来控制最佳返矿量的对策。
3) sinter production
烧结生产
1.
This paper summarizes the feasibility and results of sinter production with washed coal as fuel instead of raw coal,under the material and fuel conditions at Anyang Iron and Steel CorpIt has been proved by practices that,the content of SiO2 is reduced and the TFe of sinter is increased by this and as the consequence the technical and economic indexes of blast furnace are improve
本文论述了在安钢原、燃料条件下用洗精煤替代原煤作燃料的烧结生产可行性研究及效果。
2.
The dose of all kinds of materials and control of sinter parameters are key to sinter production.
本钢烧结生产过程由原料、配料、烧结和成品运输4个部分组成,各个部分的开关量、模拟量和控制回路多,且相互影响。
4) sintering production
烧结生产
1.
In order to improve the situation that the sintering production capacity cannot follow the increase of that in iron-making, measures are taken such as increasing pellet ore and lump ore, raising sintered ore basicity, improving properties of sintered ore and promoting the optimizing of BF burden structure.
针对随着炼铁产能的提高烧结生产能力不足的现状,通过采取增加球团矿和块矿用量、提高烧结矿碱度、改善烧结矿性能等措施,促进高炉炉料结构进一步优化,为高炉提供优质原料,满足炼铁生产。
2.
The indurical exprement and production shows that it is workable to use directly making-steel sludge in sintering production at NO2.
马钢二烧配用炼钢湿基污泥的试验和生产表明，在烧结生产中，直接利用炼钢湿基污泥是可行的，利于提高料层厚度，实现厚料层烧结，提高烧结矿产量，具有可观的经济和社会效益。
3.
The development of SHAOGANG sintering production was summerized,and the developing direction in future was forecaste
总结了韶钢烧结生产的发展过程 ,提出了今后发展的方
6) sintering process
烧结生产
1.
On the condition of guaranteeing the quality of sinter and stability of productive process, the sintering process of adding ferruginous waste such as steel-making slag, iron oxide scale and dust separately is analyzed.
实践证明 ,在烧结生产中配加钢铁废料 ,可以稳定生产 ,保证烧结矿品位合格 ,降低烧结矿成本 ,降低能源 ,合理利用资
2.
In order to decrease the cease-operation rate and stabilize the processing, an expert system for diagnosing abnormal status of sintering process has been designed and developed, whose aim is to diagnose the whole sinter.
烧结生产是一个工艺流程长、影响因素多、机理复杂的动态系统。
3.
A rule-based abnormity diagnosis expert system for sintering process has been designed and developed by means of Visual Studio.
Net和Matlab混编的方式,结合ADO数据库技术,将整个烧结生产工艺过程作为诊断对象,设计开发出基于规则的烧结生产异常诊断专家系统。
补充资料：铝酸盐炉料烧结熟料窑生产夜景(山西铝厂)
铝酸盐炉料烧结熟料窑生产夜景(山西铝厂)
铝酸盐炉料烧结熟料窑生产夜景(山西铝厂)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条