1) stochastic extraction system
随机引出系统
2) stochastic extraction
随机引出
3) extraction system
引出系统
1.
Fast kicker magnet prototype for CSNS\RCS extraction system
CSNS\RCS引出系统快脉冲冲击磁铁样机的设计
2.
45GHz microwave ion source s extraction system at the Institute of Heavy Ion Physics, Peking University.
45GHz袖珍永磁微波离子源引出系统的一项改进,即在距该离子源永磁环9cm处加一个长为10cm的永磁透镜。
3.
Further on the background of extraction system of high-power electron accelerators, which can be used to eliminate sulfur from gas, energy distribution, angle distribution, X-ray generating proportion, titanium window s heating, were simulated in the condition of different accelerating voltages, and extraction efficiency was obtained.
本文应用EGS4模拟计算程序,计算了通过双层金属箔结构式钛窗的引出系统,电子束的能量效率和束流效率,与国外的计算结果符合得较好。
4) stochastic system
随机系统
1.
Variance minimization dual adaptive control for stochastic systems with unknown parameters;
参数未知随机系统的最小方差对偶自适应控制
2.
Sufficient and necessary condition of a class I to uncertain stochastic system s mean-square stabilization stability;
一类伊藤型不确定随机系统均方稳定的充要条件
3.
LMI-based approach to robust control for distributed parameter stochastic systems with time delays;
分布参数时滞随机系统鲁棒控制的LMI方法
5) stochastic systems
随机系统
1.
Robust control of networked stochastic systems with nonlinear perturbations;
具有非线性扰动的网络化随机系统鲁棒控制
2.
Nonlinear controller of stochastic systems——back-stepping approach;
基于back-stepping方法的随机系统的非线性控制器
3.
Least squares based recursive identification for stochastic systems with colored noises;
一类有色噪声干扰随机系统最小二乘递推辨识
6) random system
随机系统
1.
In this paper, we study sone questions about a order liner random system and obtain some theroms.
本文对一阶随机系统的几个问题进行了研究,得到了几个结论。
2.
According to the survey statistics from several cities in which the taxi operating status is good,the method of birth and death process in random system theory was used and the proportion of vacant taxies and occupant ones in a reasonable scale should be from 0.
结合我国几个出租汽车运营状况良好的城市调研数据,运用随机系统理论中的生灭过程法,提出了合理规模下的空驶车与载客车的比例应该在0。
补充资料：Pro/Engineer Drawing 工程图尺寸引出线
· 5.6.1 延长/缩短尺寸线
选择move 或clip命令。
DETAIL>clip:选择尺寸确认，移动鼠标，在合适的引处线位置点left
DETAIL>move: 选择尺寸引出线端点，拖动鼠标。
· 5.6.2 显示/隐藏引出线
选择菜单：DETAIL > Modify > Dim Params > Wit Line Disp > Erase,选择引出线-----隐藏。
选择菜单：DETAIL > Modify > Dim Params > Wit Line Disp > Erase,选择尺寸-----显示。
· 5.6.3 打断/恢复引出线
选择菜单：DETAIL > break>Add，在尺寸线第一打断点点左键；在第二打断点点左键。-----ok
选择菜单：DETAIL > Modify >Remove,选择尺寸，被打断的尺寸线被恢复。
· 5.6.4 弯曲引出线
使用菜单：DETAIL > Move. ,在尺寸的箭头处按住鼠标左键，在尺寸线垂直方向移动，尺寸线被打了一个折弯。
要恢复怎么办：拉回来！！！！！！！！
还有一些，如make jog等，不常用，这里就不介绍了。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条