1) Injection and extraction system
![点击朗读](/dictall/images/read.gif)
注入引出系统
2) Injection and extraction
![点击朗读](/dictall/images/read.gif)
注入引出
3) nonlinear output injection system
![点击朗读](/dictall/images/read.gif)
非线性输出注入系统
1.
Fault estimation based on adaptive observer is studied for a class of nonlinear output injection system.
针对一类非线性输出注入系统,研究了基于自适应观测器的故障估计问题。
4) Injection system
![点击朗读](/dictall/images/read.gif)
注入系统
1.
Physical design of full energy injection system in HLS;
![点击朗读](/dictall/images/read.gif)
合肥光源满能量注入系统物理设计
2.
Development and application of nitrogen foam injection system on offshore oilfield;
![点击朗读](/dictall/images/read.gif)
海上油田氮气泡沫注入系统的研制与应用
3.
The injection system has run for almost two years and played an important role in the operation of the ligh
介绍了HLS(合肥光源)储存环注入系统建造与调试情况。
5) extraction system
![点击朗读](/dictall/images/read.gif)
引出系统
1.
Fast kicker magnet prototype for CSNS\RCS extraction system
![点击朗读](/dictall/images/read.gif)
CSNS\RCS引出系统快脉冲冲击磁铁样机的设计
2.
45GHz microwave ion source s extraction system at the Institute of Heavy Ion Physics, Peking University.
45GHz袖珍永磁微波离子源引出系统的一项改进,即在距该离子源永磁环9cm处加一个长为10cm的永磁透镜。
3.
Further on the background of extraction system of high-power electron accelerators, which can be used to eliminate sulfur from gas, energy distribution, angle distribution, X-ray generating proportion, titanium window s heating, were simulated in the condition of different accelerating voltages, and extraction efficiency was obtained.
本文应用EGS4模拟计算程序,计算了通过双层金属箔结构式钛窗的引出系统,电子束的能量效率和束流效率,与国外的计算结果符合得较好。
6) injection extraction technique
![点击朗读](/dictall/images/read.gif)
注入引出技术
补充资料:Pro/Engineer Drawing 工程图尺寸引出线
· 5.6.1 延长/缩短尺寸线
选择move 或clip命令。
DETAIL>clip:选择尺寸确认,移动鼠标,在合适的引处线位置点left
DETAIL>move: 选择尺寸引出线端点,拖动鼠标。
· 5.6.2 显示/隐藏引出线
选择菜单:DETAIL > Modify > Dim Params > Wit Line Disp > Erase,选择引出线-----隐藏。
选择菜单:DETAIL > Modify > Dim Params > Wit Line Disp > Erase,选择尺寸-----显示。
· 5.6.3 打断/恢复引出线
选择菜单:DETAIL > break>Add,在尺寸线第一打断点点左键;在第二打断点点左键。-----ok
选择菜单:DETAIL > Modify >Remove,选择尺寸,被打断的尺寸线被恢复。
· 5.6.4 弯曲引出线
使用菜单:DETAIL > Move. ,在尺寸的箭头处按住鼠标左键,在尺寸线垂直方向移动,尺寸线被打了一个折弯。
要恢复怎么办:拉回来!!!!!!!!
还有一些,如make jog等,不常用,这里就不介绍了。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条