1) ectric spot welding
电点焊
2) spot-welding electrode
点焊电极
1.
Optimization of process parameters of vibration electrospark deposition TiC on spot-welding electrode;
点焊电极表面电火花振动熔敷TiC工艺参数优化
2.
Functional TiC coating was deposited on the surface of Cr-Zr-Cu spot-welding electrode by vibrating electrospark deposition.
为了提高镀锌钢板点焊电极的寿命,以TiC为沉积材料,在铬锆铜球型点焊电极表面进行了电火花振动沉积功能涂层的工艺试验,研究了首次单点沉积、限时沉积、清洗前处理、扩散后处理等方法获得功能层的显微组织与性能。
3.
In order to improve the life of spot-welding electrode for zinc-coated steel,electrospark deposition(ESD) processes were studied taking TiC as fusing material and CrZrCu as spot-welding electrode.
为了改善镀锌钢板点焊电极的寿命,选用铬锆铜球型点焊电极,以TiC作为熔敷材料,进行了点焊电极表面电火花沉积TiC工艺试验。
3) resistance spot welding
电阻点焊
1.
Application of MEMS pressure sensor to measuring electrode force of resistance spot welding;
MEMS压力传感器在电阻点焊压力测试中的应用
2.
Design of man-machine interface system for digital 3-phase DC resistance spot welding;
数字化三相次级整流电阻点焊人机交互系统的设计
3.
Electron beam welding and resistance spot welding of time effect stainless steel cabin;
时效不锈钢舱体的电子束焊与电阻点焊
4) spot welding electrode
点焊电极
1.
Both sides electric currents,the voltage and the dynamic resistance were tested on continual spot welding process,the track test results under the different spot welding electrode active status were contrasted and analyzed,the best method of online detection of spot welding electrode active status was determined.
对连续点焊过程中电极两端电流、电压和动态电阻进行跟踪测试,并对点焊电极不同工作状态下跟踪测试结果进行对比分析,确定出在线监测点焊电极工作状态的最佳方法。
5) spot welding power source
点焊电源
1.
The hardware and software of a developed 8098 single-chip microcomputer controlled MOSFET precise spot welding power source have been introduced in the paper.
对所研制的由８０９８单片机控制的ＭＯＳＦＥＴ精密点焊电源的硬件及软件进行了介绍。
6) spot welding
电阻点焊
1.
Application of AHP method of orthogonal trial to selection of parameters in resistance spot welding;
正交试验层次分析法在电阻点焊参数选择上的应用
2.
Quality forecasting of resistance spot welding joints;
基于电极位移信号的电阻点焊质量预测模型
3.
Technology of stainless steel SUS301L spot welding was studied.
研究了SUS301L不锈钢电阻点焊的工艺。
补充资料：点焊胶粘剂
分子式：
分子量：
CAS号：
性质：用于胶接点焊工艺胶粘剂。用环氧树脂、聚硫橡胶等配合制成。具有联接强度高、密封性好、应力分布均匀、耐疲劳性好、结构重量轻、可以进行阳极氧化、生产率高等优点。可用于铝、铝合金等金属材料和玻璃钢的胶接点焊，也可用于金属材料的结构粘合和灌封等。
分子量：
CAS号：
性质：用于胶接点焊工艺胶粘剂。用环氧树脂、聚硫橡胶等配合制成。具有联接强度高、密封性好、应力分布均匀、耐疲劳性好、结构重量轻、可以进行阳极氧化、生产率高等优点。可用于铝、铝合金等金属材料和玻璃钢的胶接点焊，也可用于金属材料的结构粘合和灌封等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条