1) single-acting cylindrical cam
单动圆柱偏心轮
2) possitive motion cylindrical cam
正运动圆柱形偏心轮
3) eccentric circular cylinders
偏心圆柱
1.
This paper studies the steady streaming flow of low Reynolds number between two eccentric circular cylinders.
本文研究低雷诺数情况下偏心圆柱间定常Streaming流动问题,其中内柱以速度U(x)cosωt在静止不可压粘性流体中作小振幅直线简谐振动,外柱则固定不动。
4) circularly-eccentric sheave
圆偏心轮
1.
Analysis of the force in circularly-eccentric sheave clamping system;
圆偏心轮夹紧机构的力分析
5) eccentric cylinder
偏心圆柱面
1.
By use of complex variable function and conformal transformation,the cross-section of separation cylinder and eccentric cylinder and off-axis ellipsoidal cylinder are transformed to the cross-section of parallel plates,and the capacitance,electric potential and electric field intensity of each cylinder are calculated.
运用复变函数、保角变换等理论,把分离圆柱面形、偏心圆柱面形和偏轴椭圆柱面形变换成横截面为平行板,并计算出它们的电容、电势和电场强度等静电场问题。
6) eccentric cam
偏心圆凸轮
1.
Compared with other oscillating follower mechanical rules, analytics is made on the commoneccentric cam mechanism and power, as given the practical scope and the basic parameters.
对常用的偏心圆凸轮从动件进行运动和动力分析，并与其它从动件常用运动规律进行比较，推荐其应用范围及基本参数的选取范围。
2.
The paper brings forward and analyzes the non-dimensional formulas of setover eccentric cam from the aspects of the travel, displacement, speed and velocity of the moving parts.
提出了偏置式偏心圆凸轮机构从动件的行程、位移、速度、加速度的无量纲表达式,并对其进行分析。
补充资料：在AutoCAD中偏心圆锥与偏心圆台实体的画法
现在要画一个偏心圆锥,底面在WCS的XY平面上,圆心(0,0,0),半径100,顶点(300,0,400)在ZX平面上.
1)连接PA,PB. A(-100,0,0) B(100,0,0)
图1
在当前坐标下:
2)延长PA到C,使PA=CA;延长PB到D,使PB=DB;
3)连接CD;
4)以CD为直径画圆;
5)用XLINE命令中的二等分选项作角CPD的角平分线PO,交CD于O;
6)过O作CD的垂线,交圆于E,F;
图2
7)用三点UCS命令,取三点为:O,P,C;
8)过点O作PO的垂线GO,交PC于G;
图3
9)再次用三点UCS命令,取三点为O,F,G;
10)现在就可以画椭圆锥了!
cone-e-c-捕捉O点-捕捉F点-捕捉G点-a-捕捉P点;
图4
11)回到WCS,剖切椭圆锥
SL-选择椭圆锥-回车-XY-回车-捕捉P点.
12)删除辅助线条.
图5
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条