1) wellhead production temperature
井口产出液温度
2) wellhead temperature
井口温度
1.
The discussion about how to calculate offshore wellhead temperature
海上油井井口温度计算方法探讨
3) Outlet temperature
出口温度
1.
The result shows that the outlet temperature by partial charged method is more steady and its discharging rate is higher than that by fully charged method.
比较了两种冻结方式在蓄冷和释冷过程中的传热性能,结果表明,不完全冻结方式在释冷过程中盘管出口温度更稳定、释冷速率更高,给出了不完全冻结必须满足的条件。
2.
On the basis of on-site data and in conjunction with the working principle of a power plant coal-pulverizer system a state-space dynamic mathematical model has been set up of the coal pulverizer outlet temperature and pulverizer inlet-air flow rate through an analysis of the coal pulverizer control system.
基于现场数据 ,结合电厂磨煤机系统的工作原理 ,通过对其控制系统分析 ,建立了磨煤机出口温度和磨煤机入口空气流量的状态空间动态数学模型。
3.
Two calculation methods for combustor outlet temperature of an aeroengine were described.
概要介绍了某型航空发动机燃烧室出口温度的2种计算方法,结合发动机试车数据对采用2种计算方法得到的结果进行了对比分析。
4) exit temperature
出口温度
1.
The influnce of the surface contact conductance in crystallizing and rolling areas on the exit temperature of the strip was analysed by dividing the casting area into two segments.
将铸轧区分成结晶区和轧制区两段 ,分析了结晶区和轧制区的界面接触热导对铸坯出口温度的影响。
2.
Based on the aerodynamic calculation and using some experiential formula on flow and jet mixing,the exit temperature debugging method at a certain turbine combustor was studied according to the working condition and the overhaul experimental data.
在气动计算基础上,借鉴有关流动和射流穿透经验关系,依据发动机工况及试车测试数据,针对某型发动机燃烧室,进行了通过改变掺混孔孔径调整出口温度场分布的计算方法研究。
3.
The application of Grey models GM(1,1) in the exit temperature prediction of coal pulverizer is discussed .
探讨了灰色预测模型GM(1,1)在磨煤机出口温度预测中的应用。
5) produced fluid
油井产出液
1.
On the premise that the effects of salt and other impurity substances are eliminated,the relative molecular weight and degree of hydrolysis of polyacrylamide in produced fluid of polymer flooding reservior were accurately determined by ultra filtration technique,which were compared with that of injected polymer.
采用美国Millipore切向流超滤系统,在消除了油井产出液中盐等杂质影响的前提下,准确测定了产出液中聚丙烯酰胺的相对分子质量和水解度,并与注入聚丙烯酰胺的相对分子质量和水解度进行了对比。
2.
It uses American Millipore tangential stream ultra-filtration system and eliminates the influences of salt, surfactant and other impurities in the produced fluids on the measured results.
在聚合物驱过程中,由于聚合物相对分子质量和水解度发生变化,常规的淀粉-碘化镉质量浓度检测方法已不适用于油井产出液中聚合物质量浓度的检测。
6) surface liquid yield
井口产液量
1.
Surface liquid yield measurement using dynamometer card (SLYMUDC) is a method of computing surface liquid yield of wells by analyzing polished rod load and displacement.
示功图量油就是通过对悬点载荷与悬点位移进行分析,计算井口产液量的一种方法。
补充资料：主要经营单位进出口总额(外贸进出口总额)
主要经营单位进出口总额(外贸进出口总额)：是指经营单位在本口岸和外口岸进出口的金额。自1999年1月开始使用海关统计数据。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条