1) gating insert
浇口镶块
2) embedded lump
镶块
1.
During die casting,the embedded lump crazed reduces productivity effect of the factory.
压铸模具镶块开裂失效降低企业的生产效率,本文对一镶块开裂失效过程进行了分析研究。
3) insert
[英][in'sə:t] [美][ɪn'sɚt]
镶块
1.
The joint of perpendicular flanging insert and slanting flanging insert was one of the difficulties in automobile panel die design.
垂直翻边凹模镶块和倾斜翻边凹模镶块的交接是汽车覆盖件模具设计的难点之一。
2.
Through comparing with the horizontal thrusting force of the parts acting to the die and the spring-back force of the parts when which have been separated into the die,factors affecting insert fixing and mechanical relations are obtained.
对冲裁凹模进行了受力分析,通过工件对凹模水平方向的推力和工件分离完全被挤入凹模时的回弹力的比较,得到了镶块固定的影响因素及力学关系。
3.
The CNC programming for the machining of a blow mould insert for drink bottle is finished by using Pro /E.
利用Pro/E软件编制了饮料瓶吹塑模镶块数控加工程序。
4) inlayed block
镶块
1.
Stress on inlayed blocks of gear axis cold extrusion die and sleeves walls are modeled and ac-counted, and inlayed blocks are analyzed with ANSYS on the basis of stress result.
对齿轮轴冷挤压凹模镶块及其套筒内壁建模并进行应力计算,根据应力结果对镶块的结构利用ANSYS进行分析,找出薄弱环节进行改进性设计,以提高模具的使用寿命,为同类设计提供参考依据。
2.
The structures of convex die and concave mould of this kind of large table-board blanking die used in specialty equipments adopted the piece together form of inlayed block and the guidance of three directional re.
该种在专业设备上使用的大台面落料模,其凸凹模结构采用镶块拼接形式,双侧3向方形导柱导向。
5) insert block
镶块
1.
To this diecasting die cavity,by using inside notch core-pulling mechanism,cope with the core-pulling problem of inside notch parts; adopting insert block structure is favourable to the snapout of gas in the course of diecasting,which solves the problem of cast air holes and conspicuously increase the qualified rate and economic benefit of diecasting.
该模具型腔采用内凹抽芯机构,解决了内凹零件的抽芯问题;采用镶块结构,有利于压铸过程中气体的排出,解决了铸件气孔问题,显著提高了压铸件的合格率和经济效益。
6) Inlaied scoop
镶口
补充资料：八宝镶冬笋
八宝镶冬笋
八宝镶冬笋
原料: 原 料：
主材料：小冬笋6棵配料：冬菇9个，白果30克，素火腿30克，豆腐干3块，胡萝卜50克调味料：（1）酱油少许，淀粉2茶匙，麻油1茶匙，沙拉油2碗。（2）素高汤1碗，冬菇素蚝油1茶匙，白胡椒粉少许（3）素高汤1碗，素蚝油1茶匙，糖1/2茶匙
制法: （1）将小冬笋切去硬外壳，用挖球器将中间挖空，抹少许酱油，下油锅炸至外皮呈颜色即取出，中间抹少许淀粉备用。
（2）将冬菇、白果、素火腿、豆腐干、胡萝卜切成小丁；炒锅烧热加2碗沙拉油，加入小丁料，过油即取出，倒出锅中剩油，放入麻油，再放入全部小丁料炒香，加调味料（2），烧至汤汁收干，加淀粉勾芡即可取出，最后镶入冬笋中。
（3）每一个冬笋下均铺上一个冬菇，上笼蒸20分钟，取出装盘。炒锅放入调味料（3）烧开，加淀粉勾芡，淋上冬笋上即可
说明：补充资料仅用于学习参考，请勿用于其它任何用途。