1) recarburization coke
增碳焦
2) coke
[英][kəʊk] [美][kok]
焦碳
1.
A method named acid resolution-elementary analysis was established to determine the quality ratio of hydrogen to carbon of coke on cracking catalyst.
提出了一种测定裂化结焦催化剂上焦碳H C的方法———酸溶 元素分析法。
3) coke
[英][kəʊk] [美][kok]
焦，焦碳
4) carbon pick-up
增碳
1.
A Study on Carbon Pick-up in Ultra Low Carbon Molten Steel in Mold during Continuous Casting;
连铸时超低碳钢结晶器内钢液增碳的研究
2.
Analysis on carbon pick-up of liquid steel in CSP processing route in Magang;
马钢CSP流程钢水增碳现象的分析
3.
Progress in research on the influence of MgOC, Al2O3-C and ZrO2-C refractory upon carbon pick-up of molten steel is summarized.
叙述了MgO-C、Al2O3-C和ZrO2-C材料对熔钢增碳方面的研究进展;描述了MgO-C、Al2O3-C材料的增碳机理;指出了今后含碳耐火材料对熔钢增碳影响方面的研究重点。
5) recarburization
增碳
1.
During recarburization of the semi-steel,the bath temperature be effectively controlled by plasma heating,carbon content of semi-steel could be increased from 1.
在150 kW 等离子体感应炉内,进行了加热半钢升温、增碳和脱硫的实验。
2.
Major factors affecting liquid steel decarburization and recarburization in the process of RH vacuum treatment and continuous casting of extra low carbon steel were analytically studied based on datum obtained from the previous experiments and measures to be taken for promoting liquid steel decarburization and preventing it from recarburization recommended as well.
根据试验数据分析并研究了超低碳钢在RH真空处理和连铸过程中,影响钢水脱碳与增碳的主要工艺因素。
3.
Results show that one of the reasons causing transverse crack is recarburization in wire rod surface.
采用扫描电镜、大型金相显微镜对拉拔横裂纹试样进行观察并分析,结果表明:造成横裂纹的原因之一是盘条表面增碳。
6) Carburization
[,kɑ:bjurai'zeiʃən]
增碳
1.
Carburization of Al-bearing MgO-SiC composite to molten steel;
含铝粉的MgO-SiC材料对钢水的增碳行为
2.
Applying the mass and momentum transfer theory,the carburization mechanism of ultra low carbon steel melt caused by the carbon containing flux has been investigated Results show that,in spite of low carbon content of mold powder used for the ultra low carbon steel and low solubility of carbon in flux,the carbon of flux has a considerable influence on the carburization of the steel mel
应用质量和动量传输理论，对连铸结晶器内含碳熔渣所引起的超低碳钢钢水增碳的机理进行了研究。
3.
By means of thermodynamics calculation and analysis for samples,the carburization was further researched.
钢中的碳对超低碳钢的性能有很大的影响,针对鞍钢 ASP 中薄板坯连铸生产超低碳钢异钢种连浇过程中铸坯增碳的问题,通过理论计算和取样分析,对异钢种连浇过程铸坯增碳进行了研究,并对工艺进行改进。
补充资料：二叔丁基焦碳酸酯
分子式：C10H18O5
分子量：218.25
CAS号：24424-99-5
性质：可燃性液体。熔点23℃，沸点56-57℃（6.55E-2kPa）。
制备方法：叔丁醇钾溶于无水四氢呋喃，在-5～-20℃通入干燥的二氧化碳，生成浆状物，继续保持低温，滴加光气苯溶液，制得三碳酸二叔丁酯。将其溶于四氯化碳，加适量1,4-二氮杂二环[2,2,2]辛烷，在25℃搅拌使二氧化碳释放完全，转化为二碳酸二叔丁酯。
用途：有机合成中用来引入叔丁氧羰基保护基团。
分子量：218.25
CAS号：24424-99-5
性质：可燃性液体。熔点23℃，沸点56-57℃（6.55E-2kPa）。
制备方法：叔丁醇钾溶于无水四氢呋喃，在-5～-20℃通入干燥的二氧化碳，生成浆状物，继续保持低温，滴加光气苯溶液，制得三碳酸二叔丁酯。将其溶于四氯化碳，加适量1,4-二氮杂二环[2,2,2]辛烷，在25℃搅拌使二氧化碳释放完全，转化为二碳酸二叔丁酯。
用途：有机合成中用来引入叔丁氧羰基保护基团。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条