2) low carbon carburizing steel
低碳渗碳钢
3) mild steel
低碳钢
1.
Effect of longitudinal magnetic field on microstructure and properties of MIG weld joint of mild steel;
纵向磁场对低碳钢MIG焊焊缝组织及性能的影响
2.
Study of weldability of activating flux for A-TIG welding of mild steel;
低碳钢A-TIG焊活性剂的焊接性研究
3.
Study activating flux for mild steel;
低碳钢A-TIG焊的活性剂研制
4) Low carbon steel
低碳钢
1.
Dissipative structures of inner cracks in low carbon steel during thermal healing;
低碳钢内裂纹热愈合时的耗散结构
2.
Study on Low Carbon Steel Deoxidized by Magnesium Alloy;
低碳钢镁合金脱氧的研究
3.
Analysis on metallurgical effect of low carbon steel in No.1 top-bottom combined blowing converter in Liangang;
涟钢1号顶底复吹转炉低碳钢冶金效果分析
5) ULC steel
超低碳钢
1.
Study on the optimum process of refining ULC steel by RH degasser
RH冶炼超低碳钢的最优工艺研究
2.
Inclusions and total oxygen content in ultra-low carbon(ULC) steel were studied for the control of cluster inclusions in ULC steel.
为控制超低碳钢中的簇状夹杂物,对超低碳钢中的夹杂物和与全氧含量的关系进行了研究。
3.
The polarization curve of the ULC steel with titanium and niobium was measured to determine the suitable electrolytic parameters for preparation of TEM carbon replica samples.
测定了一种复合添加钛、铌超低碳钢的极化曲线,选用合适的电流密度和电解时间以碳复型方法萃取钢中的析出相制备透射电镜观察用样品。
6) low-carbon steel
低碳钢
1.
Testing the assessment specimens for assessing the weldability of low-carbon steel;
低碳钢焊接工艺评定试样的试验方法
2.
Analysis of necking under condition of uniaxial tension of low-carbon steel specimen based on gradient-dependent plasticity;
基于梯度塑性理论的单向拉伸低碳钢试样颈缩分析
3.
Microstructure of a low-carbon steel intercritically quenched and its recrystallization after cold rolling
亚温淬火低碳钢的组织特性及冷轧后的再结晶
补充资料：烧结碳钢
分子式：
CAS号：
性质：采用粉末冶金方法制得的碳素钢材料。强度一般为0.7GPa左右，硬度和耐磨性均优于烧结铁。通过热处理和表面硬化处理可以进一步提高其力学性能。适于制造齿轮等机械零件。原料采用铁粉和石墨粉，在0.7～1.5GPa的压力下冷压成形，然后在发生炉煤气的保护下加热至1100～1400℃烧结1～4h。烧结碳钢的组织和性能随含碳量不同而异。
CAS号：
性质：采用粉末冶金方法制得的碳素钢材料。强度一般为0.7GPa左右，硬度和耐磨性均优于烧结铁。通过热处理和表面硬化处理可以进一步提高其力学性能。适于制造齿轮等机械零件。原料采用铁粉和石墨粉，在0.7～1.5GPa的压力下冷压成形，然后在发生炉煤气的保护下加热至1100～1400℃烧结1～4h。烧结碳钢的组织和性能随含碳量不同而异。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条