1) sliding contact
滑动接触,滑动触点
2) slide contact
滑动触点,滑动接触
3) sliding contact
滑动接触
1.
Finite element analysis of head/disk continuous sliding contact was performed to investigate temperature field and thermal stress field due to frictional heat using an axisymmetric thermal model.
采用二维轴对称有限元模型计算磁头/磁盘滑动接触下,铝质磁盘的稳态温度和热应力场以及热退磁临界条件。
2.
In order to develop the critical operating conditions for demagnetization of the disk,a coupled temperature-displacement finite element analysis of a slider sliding contact with a textured disk surface was performed,so as to investigate simultaneously the stress and temperature distributions in the magnetic layer.
采用应力场和温度场耦合的有限元方法,计算磁头/磁盘滑动接触下铝基磁盘磁层内瞬态温度场和应力场及退磁临界条件,分析接触压力、滑动速度、摩擦系数以及磁盘表面纹理对磁层内最大摩擦温升值和最大应力值的影响。
3.
Also the stess distribution problem in the half space with gradient layers coating is considered and compared with the homogeneous half space and half space with single layer coating under same sliding contact load and in plastic deformation condition.
对粗糙面在梯度表面层上的滑动过程进行应力分布研究 ,以模拟实际摩擦过程中 ,考虑塑性变形情况下 ,梯度覆层体中的应力分布规律 ,同时与均质体及单覆层体进行比较研究 ,分析了在表面载荷相同时滑动接触的应力分布。
4) rabbing contact
摩擦接触滑动触点
5) rolling/sliding contact
滚滑动接触
1.
It is in this model that the influence of lubricant on stress intensity factors of surface initial fatigue lean crack in rolling/sliding contact has been analyzed through using the collapsed 8 node quadrilateral isoparametric elements and numerical extrapolated method.
文章建立了二维具有初始滚滑动接触疲劳表面斜裂纹的模型。
6) sliding electrical contact
滑动电接触
1.
The effect of carbon fiber on sliding electrical contact property of copper-graphite composite materials has been studied.
根据目前电力机车受电弓滑板应用的背景研究了在铜 石墨复合材料中加入碳纤维后对复合材料滑动电接触性能的影响。
2.
5-MJ capacitor bank has been developed to investigate high-current high-velocity sliding electrical contacts.
为提供电接触大电流,驱动电磁轨道发射装置将试品加速到1~2km/s的高速以模拟速度转捩的发生条件,研制了用于大电流高速滑动电接触实验研究的1。
3.
In order to research the sliding electrical contact characteristics of Cu-base powder metallurgy strip under sliding electrical contact conditions,a lot of experiments were carried out with a self-developed high-performance sliding electrical contact testing instrument.
利用自行研制的高性能滑动电接触实验机,对铜基粉末冶金滑板的滑动电接触特性进行实验研究。
补充资料:腹股沟滑动性疝修补术
腹股沟滑动性疝修补术
repair of sliding inguinal hernia
滑动性疝均应手术修补。一般采用经腹股沟修补术。麻醉、切口和显露疝囊的手术步骤与斜疝手术相同。显露疝囊并切开,然后在滑出内脏(例如盲肠)的周围约1.5cm处作一环形切口,切开腹膜(即疝囊),在腹膜外游离盲肠,直至疝囊颈部(内环)外。注意勿损伤肠管的动、静脉。将游离的盲肠显露于切口外,在其后面将两侧腹膜作间断对合缝合,使其成为一个新的完整疝囊。然后,将游离的盲肠回纳入腹腔,在内环外用丝线作一荷包缝合,以关闭腹腔,剪除多余疝囊。然后施行Bassini或McVay术修补腹股沟管。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条