1) run-on tab
[焊接]引弧板
2) end tab
(焊接)引弧板
3) submerged arc welding
埋弧焊接
1.
Effect of arc offset on the quality of submerged arc welding and improving measures of the welding technology;
弧偏吹对埋弧焊接质量的影响和焊接工艺改进措施
2.
Based on Buck DC/DC converter,an arc stability controller was designed for submerged arc welding(SAW).
基于Buck DC/DC变换器,设计了埋弧焊接(Submerged arc welding,SAW)过程的稳弧控制器。
4) welding arc
焊接电弧
1.
Study on the effect of the ZA alloy TIG flux on the weld formation and welding arc;
ChinZA合金TIG焊剂对焊接电弧及焊缝成型的影响
2.
Variable polarity TIG welding arc dynamic analyzer;
变极性TIG焊接电弧多信息测试分析系统
3.
Spectral space character of welding arc and its applications;
焊接电弧光谱的空间特征及应用研究
5) argon arc welding
氩弧焊接
1.
The friction stir welding of 2mm thick 01420 Al-Li alloy was conducted,the microstructures,qualities of joining,and mechanical properties of the joints as well as the influences of welding parameters on the alloy were investigated,meanwhile comparing the mechanical properties with that of the joint welded by argon arc welding.
对2 mm厚的01420铝锂合金薄板实现了搅拌摩擦焊接(FSW),分析焊接接头的微观组织形态,研究焊接工艺参数对搅拌摩擦焊接接头成型和接头性能的影响,并与氩弧焊接接头性能相比较。
2.
It also gave the reason of the crack which is produced in the splice welded seam, and madea clear summary of the practice in controlling the technical process of argon arc welding.
介绍了抛物面天线整体旋压成型的工艺过程,针对旋压过程铝板拼接焊缝开裂的原因进行了初步分析,并对氩弧焊接工艺控制过程的经验进行了总结。
3.
The technology of microcomputer monitor system which applied in argon arc welding procedure of the manufacture of automatically activated primary Zn AgO batteries was introduced.
介绍了由微机和监视技术组成的监控装置在自动激活一次锌氧化银电池制造工艺中氩弧焊接技术上的应用,着重阐述该系统中的监控装置、焊接装置及I/O接口控制电路。
6) weld arc length
焊接弧长
1.
Backing weld procedure technique of all position narrow gap and thick walled pipe welding is developed about all position single pass welding section analysis,wire feeding behavior , weld arc length , welding current analysis,procedure and joint test.
从单焊道全位置区段、送丝行为、焊接弧长 (电压 )、电流行为分析、工艺试验和接头检验等几方面介绍管道全位置打底焊工艺特点 ,其研究成果对全位置焊接机的制造和调试具有普遍指导意义。
补充资料:焊接:埋弧焊
利用在焊剂层下燃烧的电弧进行焊接的方法(见图 埋弧焊示意图 )。在焊接过程中﹐焊剂熔化產生的液态熔渣覆盖电弧和熔化金属﹐起保护﹑净化熔池﹑稳定电弧和渗入合金元素的作用。埋弧焊分为自动埋弧焊和半自动埋弧焊两种。前者应用较广泛﹐焊接电流可达600~2000安﹐焊接效率很高。埋弧焊是一种适於大量生產的焊接方法﹐广泛用於焊接各种碳钢﹑低合金钢和合金钢﹐也用於不锈钢和镍合金的焊接和表面堆焊。为了提高焊接效率和扩大使用范围﹐埋弧焊的电极可採用双丝﹑三丝﹑带极(用於堆焊)﹐还可在焊剂中添加金属粉等。焊剂层下的电弧与焊件接口的对正和调整﹐可用工业电视观察或用激光跟踪等方法探测。埋弧焊的焊接效率高﹐焊缝光洁﹐无飞溅﹐少烟尘﹐无电弧闪光﹐劳动卫生条件好﹐设备成本较低。缺点是限於平焊和长焊缝。与气体保护电弧焊相比﹐埋弧焊电弧不可见﹐接头装配要求较高﹐应用灵活性也较差。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条