1) fold
[英][fəʊld] [美][fold]
折，折叠
2) crease folding
皱折折叠
3) folding
[英]['fəʊldɪŋ] [美]['foldɪŋ]
折叠
1.
Optimization of synthetic and folding conditions of a novelω-conotoxin peptide SO3;
新芋螺毒素SO3的合成优化与折叠关系
2.
Design and manufacture for folding multi-purpose patient bed;
折叠式流动性病床的设计与制作
4) lap
[英][læp] [美][læp]
折叠
1.
Surface defects have observed on outside surface of four hot reheat steam pipe bends,on the basis of the performed inspections and analysis,conclusion have been made as follows :the defects observed on outside surface of the four pipe bends are laps which can be attributed to improper heating the ingots and improper rolling parameters.
某300 MW热电机组热再热管道4支钢管在中频弯制中出现横向开裂,通过对成分、组织性能和在现场进行宏观检验,基本判定开裂原因是由于热轧参数不正确或坯料加热不良等原因在热轧中产生折叠,而所产生折叠在后续的外表机加工工序中未被充分去除所致。
5) refolding
折叠
1.
Sr~(2+)-induced stabilization and refolding of anticoagulation factor I from the venom of Agkistrodon acutus;
Sr~(2+)诱导尖吻蝮蛇毒中抗凝血因子I的结构稳定性及重新折叠(英文)
2.
Studies on the Refolding of Recombinant IL-2 in Vitro;
重组白细胞介素2体外折叠的实验研究
3.
GroE Purification and the Refolding of Recombinant Proteins as Facilitated by Chaperones;
伴侣分子（GroE）纯化及其催化的重组蛋白质折叠反应
6) fold
[英][fəʊld] [美][fold]
折叠
1.
Clinical Observations on Phacoemulsification and Foldable Intraocular Lens Implantation through a Small Cornea Incision;
角膜小切口超声乳化白内障吸除及折叠式人工晶体植入的临床疗效比较
2.
Cigarette cartons are conveyed onto stacking unit through the infeed conveyor belt,then pushed into opened case with inner flaps of the case cover folded,the out-flaps are folded after heating melt glue is sprayed on the inner flaps,and in the end,the codes are printed in the case.
条烟通过输入输送带送入堆叠站堆叠,后被推入打开的纸箱中,内箱盖被折叠,被喷上热熔胶,再折叠外折叠盖,最后在箱体上打上号码,完成装封箱。
3.
It analyses the traits and causes of the folds appeared in tube of the semi axis housings.
分析了半轴套管成形过程中出现折叠的特点和形成原因 ,并根据折叠形成原因提出了相应的预防措施 ,从而解决了生产过程中存在的质量问题。
补充资料：表面皱折
分子式：
CAS号：
性质：纤维出现弯曲、扭曲与其他纤维非准直性状态。表面皱折通常发生在复合材料表面层与次表面层。形成表面皱折的原因，大致为复合材料毛坯叠层不紧密，层与层之间存在滑移的可能性；固化过程中，模具不平整，引起表面的高低不平以及模具材料皱折除局部出现富树脂区与贫树脂区外，表面层纤维承载能力大大削弱，也影响复合材料外观形貌。防止复合材料表面皱折的措施是对复合材料毛坯进行预压实与预吸胶，选用与复合材料相匹配的模具材料，模具尽可能地光滑。
CAS号：
性质：纤维出现弯曲、扭曲与其他纤维非准直性状态。表面皱折通常发生在复合材料表面层与次表面层。形成表面皱折的原因，大致为复合材料毛坯叠层不紧密，层与层之间存在滑移的可能性；固化过程中，模具不平整，引起表面的高低不平以及模具材料皱折除局部出现富树脂区与贫树脂区外，表面层纤维承载能力大大削弱，也影响复合材料外观形貌。防止复合材料表面皱折的措施是对复合材料毛坯进行预压实与预吸胶，选用与复合材料相匹配的模具材料，模具尽可能地光滑。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条