|
|
|
说明：双击或选中下面任意单词，将显示该词的音标、读音、翻译等；选中中文或多个词，将显示翻译。
|
|
|
1) cinch bolt
胀紧螺栓
2) expansion bolt
膨胀螺栓
1.
Improved construction method of expansion bolt and annectent reinforcing bar in shell frame filled-wall;
填充墙拉结筋膨胀螺栓施工方法的改进
2.
Stress field analysis of hollow brick anchored by new expansion bolt
新型膨胀螺栓锚固下空心砖的应力场分析
3.
Based upon comparison of working principles of traditional expansion bolt and flat head inner expansion bolt the installation process of GRC is discussed.
介绍了GRC构件的特点及操作中易出现的问题,比较了传统膨胀螺栓和平头内膨胀螺栓的使用原理,探讨了GRC的安装过程,明确了GRC构件的重点控制要点,确保GRC工程的耐久性。
3) expansion bolts
膨胀螺栓
1.
Experiment on pullout and shearing resistances of expansion bolts in CS panel;
CS板内膨胀螺栓的抗拔与抗剪承载力试验
2.
a technology how to ensure the fitting quality of the expansion bolts was introduced to improve the fitting quality of stone curtain wall when expansion bolts are used to connect the curtain wall and the major structure.
本文介绍了在石材幕墙工程中采用膨胀螺栓连接幕墙与主体时,如何确保膨胀螺栓的安装质量,从而提高石材幕墙工程的安装质量。
4) foot-terra bolts
胀锚螺栓
5) Fastening bolt
紧固螺栓
1.
Fastening bolts at valve on gas tower was cracked after used 6 months.
储气塔运行半年即发生了阀门紧固螺栓的断裂事故。
2.
This article makes clear analyses on the damage occurred frequently on the fastening bolt.
文章从隔爆外壳紧固螺栓容易损坏的两个方面进行了分析 ,并就紧固螺栓的设计从螺栓强度、铸铝外壳螺纹牙强度、螺栓的预紧力矩的计算、螺栓的防松及精度等方面进行了设计举例 ,供从事防爆电气行业的有关人员参考和借
3.
The fastening bolts of steam turbine cylinder case were in fatigue-creep interaction.
调峰机组频繁调整负荷,汽轮机汽缸紧固螺栓处于疲劳-蠕变交互作用,对紧固螺栓多轴应力下疲劳-蠕变损伤的研究对调峰机组安全运行和维修具有重要意义。
6) Drag bolt
拉紧螺栓
1.
The problems of breaking of the drag bolts and falling off of the nuts on ST draft gears found in the inspection are analyzed.
对检测中发现的ST型缓冲器拉紧螺栓折断、螺母脱落问题进行了分析,并提出了改进建议。
补充资料：齿轮轮齿渐开线、螺栓、弹簧autolsp源程序
一、齿轮轮齿渐开渐开线 (defun c:gear(/)
(
setq
p0 (getpoint"输入齿轮中心p0: ")
m (getreal"输入齿轮模数M: ")
z (getint"输入齿轮齿数Z: ")
ha 1
c 0.25
a (/ pi 9)
ra(/ (* (+ z (+ ha ha)) m) 2)
rf(/ (* (- z (+ (+ ha ha) c)) m) 2)
r(/ ( * m z) 2)
rb ( * r (cos a))
ri rb
ang 0
g (polar p0 ang rb)
)
(command "circle" p0 ra)
(command "circle" p0 rf)
(command "circle" p0 r)
(command "line" g)
(while (< ri ra)
(setq
ang ( + ang(/ pi 360))
ri ( / rb (cos ang))
cta ( - (/ (sin ang) (cos ang)) ang)
g(polar p0 cta ri)
) (command g)
)
(command )
)
二、螺旋源程序
(defun errMsg (s)
(if (/= s "function cancelled") (princ (strcat "\nError: " s)))
; 当命令执行时出现错误
(setvar "cmdecho" ocmdold) ; 例如用户按下了CTRL + C
(setvar "osmode" osmold)
(setq *error* olderr) ; 恢复旧的错误处理
(princ)
) (defun c:3Dthread (/ radouter threadpitch threadlength threadangle
ptStart innerdiafactor radmid radinner ocmdold osmold 4H 5H 6H h6 g6)
;-------------------------------------------------------------------
; 获取公制外径大小、螺距总长
; 然后计算一系列几何点
; 并且关闭对象捕捉、命令回显
;-------------------------------------------------------------------
(setq 4H (list 0.0015 0.002 0.002 0.0025 0.003 0.0035 0.004 0.005 0.006 0.007 0.008 0.009 0.010))
(setq 5H (list 0.002 0.0025 0.003 0.004 0.0045 0.0055 0.0065 0.0075 0.009 0.010 0.0115 0.0125 0.0135))
(setq 6H (list 0.003 0.004 0.0045 0.0055 0.0065 0.008 0.0095 0.011 0.0125 0.0145 0.016 0.018 0.020))
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条
|