2) heating element
发热元件
1.
Microstructure and properties of an MoSi_2 heating element modified by ceramic compound;
陶瓷矿物改性MoSi_2发热元件的组织结构和性能
2.
The content and microstructure of scale of Kanthal Super 1700 MoSi2 heating element were studied using scanning electron microscope(SEM) with energy dispersive spectrometer(EDS).
采用SEM和EDS技术研究了国外某MoSi2发热元件表面保护膜的成分和微观组织。
3.
Based on the X-ray diffraction analysis(XRD),scanning electron microscope(SEM) with energy dispersive spectrometer(EDS),the composition and microstructure of Riken MoSi2 heating element after high-temperature application was studied.
采用X射线衍射、扫描电镜和能谱分析技术研究了国外某MoSi2发热元件的组成和结构。
3) heat transfer component
传热元件
1.
By using CFD software FLUENT,numerical simulation for the three-dimensional flow of air between honeycombed plate heat transfer components is carried out.
应用CFD软件FLUENT对蜂窝板传热元件板间空气的三维流动进行了数值模拟。
4) heating element
加热元件
1.
Homogeneously heating can be obtained by employing the steel tiles as thermal balance medium in horizontal roller track style tempering oven and the steel tile can also act as a protector of heating element.
采用钢瓦作为水平辊道式钢化炉热平衡介质,实现了均匀加热,并对加热元件有保护作用。
2.
A trapezoid heating element used in plate film evaporator was presented in this article.
本文提出一种在板式自由流降膜蒸发器中使用的梯形加热元件 ,可使得加热元件上、下端的液膜厚度保持一致 ,避免了壁面的干涸现象 ,极具实用价值。
3.
In the paper,the authors analyse the damage reasons of traditional Ni Cr Heating elements,and introduce both the advantages and the economic effects of adopting silicon carbide rods as heating elements.
分析了反射式铝保温炉传统加热元件 Ｎｉ Ｃｒ 电热合金过快损坏的原因。
5) electric heating element
电热元件
1.
Optimized preparation process of silicon carbide electric heating element;
SiC电热元件制备工艺的优化
2.
The structure figures of the furnace and its electric heating element before and after reform are given.
对钢丝电加热热处理炉进行改造 ,分析改造前热处理炉存在的问题 ,给出改造前后炉子结构图和电热元件结构图。
6) electrical heating element
电热元件
1.
AlN electrical heating element is designed and fabricated.
设计并制备了AlN电热元件,电热元件由AlN陶瓷基片及其附着其上的通电线路Pt组成。
2.
Al_2O_3,Fe_2O_3 and H_3BO_3 are added to the raw material a-SiC,which are sinteed as SiC electrical heating element.
以 a-SiC 为原料添加 Al_2O_3、Fe_2O_3、H_3BO_3进行了 SiC 电热元件的烧结,研究了不同助剂的含量对 SiC 电热元件的密度、气孔率、电阻率的影响,还研究了混合添加剂对 SiC 电热元件的影响。
补充资料：氧化锆发热元件
氧化锆发热元件
氧化锆发热元件
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条