1) tangential resistance
接切阻力
2) cutter top resistance
切顶阻力
1.
Through changing the face support fashion,the hard roof is managed by cutter top supports to increased cutter top resistance in Qitaihe Tiexi Coal Mine.
七台河铁西煤矿通过改变工作面支护方式,使用切顶支架增大切顶阻力来管理坚硬顶板,使坚硬顶板得到了较好的控制,杜绝了顶板事故的发生。
3) Cutting resistance
切割阻力
1.
In this paper,the relationship of the cutting resistance,the cutting power and the direction of the cutting knife cutting into the stem was introduced.
介绍了割刀切入茎秆的方向与其切割阻力和功率消耗的关系,从力学试验结果和运动几何分析两个方面说明滑切比正切省力,分析了3种切割方式切割阻力差异,确定了切割方式和切割阻力的相互关系,找到了滑切省力的原因,为以后设计各种各样的切割刀具提供了理论基础和指导方向。
4) tangential resistance
切向阻力
1.
Slope stability analysis considering tangential resistance of reinforcement;
考虑加筋切向阻力的土坡稳定分析
2.
The factors affecting tangential resistance between coal and working parts,such as water content of coal and normal pressure,are analyzed.
分析了煤的含水量及所受的正压力对煤与工作部件切向阻力的影响 ,并应用表面电渗技术减少煤的切向阻力。
5) cutting resistance
切削阻力
1.
The results testified the feasibility of the cutting mechanism and showed the sequences of test factors according to the influence on cutting resistance and cutting-out ra.
试验结果检验该半旋转切削机构的可行性及分析得出了影响切削阻力试验指标和切削成功率试验指标的主、次试验因素。
2.
The result of experimentation can be expressed as follows:The cutting resistance increasing rapidly in the beginning of cutting into the stock,it comes to the max when cutting about 2mm into the stock,then decreasing slowly.
实验表明:切削阻力在进入砧木初期迅速增大,在切深2mm左右达到最大,以后逐渐减小;切削阻力在试验条件下小于300N。
3.
On the basis of experiments, the experimental results show the limitedload of anti-compression, the highest cutting resistance and the minimum cutting line-speed, and show that the diameter of se.
试验结果得出毛桃树苗抗压伤极限载荷、毛桃苗切削最大阻力和刀片的最小极限切削线速度;以及影响毛桃苗切削的因素关系,苗木直径、转速、滑切角依次影响切削阻力大小,苗木直径与切削阻力呈平方关系;转速与切削阻力呈线性关系;滑切角与切削阻力也呈线性关系。
6) shear resistance
剪切阻力
补充资料：肺循环阻力(或全肺阻力)
肺循环阻力(或全肺阻力)
pulmonary circulation resistance
血液在肺部血管内流动时和血管壁之间的摩擦力和血液内部的摩擦阻力。肺动脉管壁较薄，分支短而管径大，故肺动脉的可扩性较大，对血流的阻力很小，仅0.12PRU(外周阻力单位)。肺循环动脉部分总的阻力和静脉部分总的阻力相等，故血液流动时在动脉部分的压力降落和静脉部分的压力降落相等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条