1) total solids
全部固体颗粒
2) solid particle
固体颗粒
1.
Effects of ultrasonic wave on the surface properties of solid particle;
超声波对固体颗粒表面性质的影响
2.
Investigation on boiling heat transfer enhancement and anti-scaling process by using solid particles;
固体颗粒强化液体沸腾换热和抗垢特性的研究
3) solid grain
固体颗粒
1.
Through studying the reasons that solid particle erosion is generated in supercritical turbine during manufacture and operation, take measures by optimization and spray harden in flowing part and flexible application of by-pass system, avoiding to happen solid grain corroding phenomenon effectively.
通过研究超超临界汽轮机固体颗粒侵蚀产生的原因,在制造和运行中采取通流部分优化及喷涂硬化、灵活运用旁路系统等防治措施,可有效降低固体颗粒侵蚀现象的发生。
2.
Incipient motion of solid grain in solid-liquid two\|phase flow is often concerned in many petroleum technologies, such as horizontal drilling, gravel-packing and sand washing.
水平井钻井、砾石充填及冲砂等作业都涉及到固液两相流动的固体颗粒起动问题。
4) solid particles
固体颗粒
1.
Analysis of group settling velocity for solid particles;
固体颗粒的群体沉降速度分析
2.
Lagrangian model for the motion of solid particles and air bubbles in the flow field of an arbitrary incompressible fluid is developed.
建立了固体颗粒和空泡在不可压缩流体任意流场中运动的Ｌａｇｒａｎｇｉａｎ模型，考虑了浓度等因素对固体颗粒和空泡运动的影响，给出了计算固体颗粒和空泡的数值方法，并模拟了一水泵叶轮中的固体颗粒和空泡运动，得出了水泵叶轮流场中固体颗粒和空泡的运动特性，为分析水力机械的磨损提供了可行的数值模拟方法。
3.
According to the fact that profile modifier of solid particles is always used in the waterflooding profile modification, a numerical simulation is carried out.
针对调整注水剖面实践中固体颗粒型调剖剂使用较多这一实际，开展了调剖数值模拟研究。
5) Solid granule
固体颗粒
1.
Experimental analysis of the pressure-carrying performance of solid granules medium;
固体颗粒介质的传压性能实验研究
6) particle
[英]['pɑ:tɪkl] [美]['pɑrtɪkḷ]
固体颗粒
1.
In this paper, the dynamic forces acting on the particles and the radial movement of particles in hydrcyclone are studied on the basis of experiment and CFD simulation.
在试验和流场数值模拟的基础上,对水力旋流器内部固体颗粒的运动行为进行了具体的研究。
2.
The particles mixing behavior in the coke-burning riser(186mm ID,height 10m)of a novel combined coke burner was studied through measuring the residence time distributions(RTD)of particles by using phosphor particles as tracers.
采用脉冲磷光颗粒示踪法对一套新型组合烧焦装置的烧焦管(内径186mm,高10m)内固体颗粒的停留时间分布进行了测试,研究了烧焦管内固体颗粒的混合特性。
3.
In order to research the characteristics of particles and its effecting mechanism to lubrication and wear,it is important that show three-dimensional shape of particles.
为了深入研究固体颗粒污染物的特性以及对摩擦副滑润、磨损影响的机制,确定固体颗粒的三维特征变得十分重要。
补充资料：固体颗粒交换系数
分子式：
CAS号：
性质：在剧烈湍动的流化床内，颗粒处于环流中，上升的固体颗粒流相当于尾涡，而下降的固体颗粒流仍是乳化相本身。在两相之间的固体交换速率可近似地取作颗粒进出尾涡的流量。可见气泡尾涡中的颗粒在气泡上升的过程中是不断更新的。吉田等导出计算固体颗粒交换系数K的方程式如下：式中，εmf为床层临界空隙率；δ为流化床内的气泡分率；umf为临界流化速度；db为气泡直径
CAS号：
性质：在剧烈湍动的流化床内，颗粒处于环流中，上升的固体颗粒流相当于尾涡，而下降的固体颗粒流仍是乳化相本身。在两相之间的固体交换速率可近似地取作颗粒进出尾涡的流量。可见气泡尾涡中的颗粒在气泡上升的过程中是不断更新的。吉田等导出计算固体颗粒交换系数K的方程式如下：式中，εmf为床层临界空隙率；δ为流化床内的气泡分率；umf为临界流化速度；db为气泡直径
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条