2) CPET
结晶化聚对苯二甲酸乙二酯
3) Amorphous poly(ethylene terephthalate)
非晶聚对苯二甲酸乙二酯
4) PET
[英][pet] [美][pɛt]
聚对苯二甲酸乙二酯
1.
Study on the Preparation, Structure and Properties of PET/Montmorillonite Based Nanocomposites;
聚对苯二甲酸乙二酯/蒙脱土纳米复合材料的制备及结构性能研究
2.
PET/nano BaSO4composites were manufactured by melt blending process.
通过熔融共混法制备聚对苯二甲酸乙二酯(PET)/纳米BaSO4复合材料,研究了纳米BaSO4对PET结晶行为、力学性能及热性能的影响。
3.
The research development of poly(ethylene terephthalate)(PET)blended with polypropylene (PP)was reviewed.
综述了聚对苯二甲酸乙二酯(PET)和聚丙烯(PP)共混的研究进展。
5) Poly(ethylene terephthalate)
聚对苯二甲酸乙二醇酯
1.
Poly(ethylene terephthalate)(PET)and PA5935 were blended in a high speed mixer,and then injected into specimense.
将聚对苯二甲酸乙二醇酯(PET)与PA5935高速共混,注射制样,样品的热性能、力学性能、阻燃性能和流变性能等测试结果表明,在PET中加入少量PA5935改善了PET抗熔滴性能与炭化性能,但结晶度、氧指数和部分力学性能下降。
2.
The immiscible poly(ethylene terephthalate)(PET)/polypropylene(PP)blend was prepared by melt mixing and its structural rheology was studied.
通过熔融共混制备了不相容的聚对苯二甲酸乙二醇酯(PET)/聚丙烯(PP)复合体系,研究了复合体系的结构流变学。
3.
The feasibility of in-situ microfibrillar method on recycling poly(ethylene terephthalate)(PET) and high-density polyethylene(HDPE) mixtures was carried out by four repetitive extrusion.
研究了原位微纤化方法在回收聚对苯二甲酸乙二醇酯(PET)和高密度聚乙烯(HDPE)混合物方面的应用。
6) poly(ethylene terephthalate)
聚对苯二甲酸乙二酯
1.
Research on non-isothermal crystallization kinetics of poly(ethylene terephthalate);
聚对苯二甲酸乙二酯非等温结晶过程研究
2.
The non-isothermal degradation processes of poly(ethylene terephthalate)(PET) and poly(ethylene 2,6-naphthalate)(PEN) blends were studied by using thermogravimetry(TG) analysis in nitrogen.
研究了惰性气氛下聚对苯二甲酸乙二酯(PET)/聚对萘二甲酸乙二酯(PEN)共混物的非等温热分解行为及其动力学。
3.
The poly(ethylene terephthalate) /montmorillonite nanocomposites are prepared by melt intercalation process and the crystallization behaviors, mechanical properties and dyeing properties of the fibers are studied in detail .
采用熔融插层法制备聚对苯二甲酸乙二酯(PET)/蒙脱土(MMT)纳米复合材料,对其纤维的结晶性能、力学性能及染色性能进行详细研究。
补充资料:结晶化聚对苯二甲酸乙二酯
分子式:
CAS号:
性质:在聚对苯二甲酸乙二酯树脂中加入成核剂,在加热和/或冷却条件下使其高速结晶化制得的产品。接近于熔融温度(250℃)的状态下变形。可用作耐热用食品容器,如烘箱和微波炉用托盘等。
CAS号:
性质:在聚对苯二甲酸乙二酯树脂中加入成核剂,在加热和/或冷却条件下使其高速结晶化制得的产品。接近于熔融温度(250℃)的状态下变形。可用作耐热用食品容器,如烘箱和微波炉用托盘等。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条