2) combined stress
![点击朗读](/dictall/images/read.gif)
复合应力
1.
The combined stresses on the shear-compression zone of concrete slabs at the momemnt of punching failure are analyzed by the twin-shear stress three-parameter strength criterion, and the ultimate vertical shear stress on the shear-compression plane is obtained.
将混凝土板的冲切破坏简化为平面应变问题,采用双剪应力三参数强度准则对冲切破坏时的混凝土板剪压区的复合应力进行分析,得到了剪压面上的极限竖向剪应力,利用静力平衡条件求得混凝土板的极限冲切承载力计算公式。
3) composite stress
![点击朗读](/dictall/images/read.gif)
复合应力
1.
The composite stress factor and pre-tensile force loss of the two diameter high strength bolts of M27 and M24 are experimentally determined in the paper.
本文对M27和M24两种直径高强度螺栓进行了复合应力系数测定和预拉力损失试验。
4) complex stress arch
![点击朗读](/dictall/images/read.gif)
复合应力拱
1.
Results show that,there is a complex stress arch composed by high stress binds,where an external-stress-arch bears weight of strata and overburden and transmit the stress into the virgin coal seam in the vicinity of working face,while an inner-stress-arch bears weight of roof and transmit the stress onto coal pillars.
结果表明,采场上方存在高应力束组成的"复合应力拱","外应力拱"承担覆岩及地表土的自重并将其传递至采场两侧实体煤内,"内应力拱"主要承担悬空顶板的重量并传递至煤柱。
5) complex stress field
![点击朗读](/dictall/images/read.gif)
复合应力场
1.
HDPE pipes were extruded by using a self-made extrusion die with complex stress field of shearing frist and then drawing during extrusion.
用自行研制的能产生先剪切后拉伸的复合应力场挤出成型装置,挤出高密度聚乙烯(HDPE)管材,对管材周向、轴向力学性能进行了初步的研究。
2.
Biaxial self-reinforced metallocene linear low density polyethylene sheet was prepared by the die with complex stress field in solid state.
主要采用一种具有复合应力场的挤出口模,通过固态挤出茂金属线性低密度聚乙烯获得双向自增强片材。
3.
Biaxially self-reinforced HDPE sheet was prepared by the die with complex stress field on the solid state.
采用具有复合应力场的挤出口模 ,固态挤出HDPE以获得双向自增强片材。
6) compound stress field
![点击朗读](/dictall/images/read.gif)
复合应力场
1.
The finite element software of 2D—σ is used to make a numerical analysis of deep roadway's stability in compound stress field.
选用 2D—σ有限元计算软件对深部巷道围岩在复合应力场中的稳定性进行了数值分析 ,着重讨论深部巷道围岩的变形特征、塑性区发育特征、围岩应力分布特征和围岩破坏机理 ,提出了合理的支护对
补充资料:拱坝应力分析
拱坝应力分析
stress analysis of arch dam
gongba yingli fenxi拱坝应力分析(stress analysis of arehdam)研究拱坝坝体和地基在各种荷载作用下的应力和变形的方法。在拱坝设计中,拱坝体形和厚度的选择,混凝土标号及地基软弱部位的加固等,均须参照应力分析的结果来确定。拱坝的应力分析,包括数学分析、结构模型试验和原型观测。原型观测是在已建成的坝上进行观测,了解其工作安全状况,校验设计结果,并为以后的科学研究提供资料。 拱坝由于结构复杂,小型工程可采用拱冠梁法。对于大型工程,过去多采用拱梁试(分)载法和结构模型试验。薄拱坝有采用有限差分法的。20世纪70年代起,逐渐采用有限单元法。 为了统一标准,在规定最大设计应力的同时,须规定应力分析方法。因拱坝的应力分布和最大拉、压应力,常随分析方法而改变。考虑各国已建成的大型拱坝都有拱梁试(分)载法的计算结果,拱坝应力分析如采用拱梁试(分)载法,可与已建拱坝进行对比,便于作出安全的评价。 拱梁试(分)载法将空间壳体化为杆系来计算,力学概念明晰,在计算过程中,能逐渐了解其力学机理,便于修改体形和调整厚度,但只能算出坝体应力。在分析地震反应、孔口影响及地基不均匀性等方面,不如有限单元法好。目前,国内外均有拱梁试(分)载法和有限单元法的通用程序。一些大型拱坝设计,常同时采用这两种方法,有时还辅以结构模型试验。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条