1) mechanism of convex at central section
中凸机构
2) cam type centring device
凸轮式中立机构
3) Cam mechanism
凸轮机构
1.
The motion simulation and research of cam mechanism based on UG;
基于UG的凸轮机构运动仿真研究
2.
The research on the kinematic characteristics of follower’s parabolic motion in cam mechanism;
凸轮机构推杆的等加速等减速运动规律的研究
3.
Parametric control of speed fluctuation minimization in cam mechanism;
凸轮机构速度波动最小化参数控制
4) cam-drive mechanism
凸轮机构
1.
According to the requirement of the technology,a new type of reciprocating pump with cam-drive mechanism resulting in the constant flow was designed.
针对注聚合物驱油的工艺要求 ,研制了新型凸轮机构恒流量往复泵。
2.
The special cam-drive mechanism which has replaced the traditional crack-connecting rod mechanism is used as the power end of the new constant discharge pump, which has greatly changed the performance of the reciprocating pump.
从柱塞运动规律、动力特性、吸入与排出性能以及泵阀工作特性等方面,对凸轮机构恒流量往复泵与曲柄连杆机构往复泵的性能进行了对比分析,从而得出了这两种往复泵存在的优点与不足,为在不同场合进一步使用好两种往复泵提供一些理论指导。
5) cam mechanisms
凸轮机构
1.
Meshing theory of involute screw worm indexing cam mechanisms;
渐开线螺旋廓面包络蜗杆分度凸轮机构的理论分析
2.
In this (paper,) procedures for the synthesis of main dimension of planar cam mechanisms with (transla-)[FQ(5.
根据凸轮基本尺寸与压力角之间的关系 ,采用求解非线性方程和线性方程的方法 ,在满足压力角限制条件下 ,确定了凸轮机构的基本尺寸 ,并用实例对求解过程进行了说明。
3.
The conception of the enveloping worm indexing cam mechanism (EWICM) is proposed by the first time, and the kinematic and geometric characteristics model of EWICM is established through introducing worm gear drive techniques to indexing cam mechanisms.
首次提出了包络蜗杆分度凸轮机构的基本构思，即将业已成熟的蜗轮蜗杆（及齿轮）传动原理与技术，引入到分度凸轮机构的研究中，建立了包络蜗杆凸轮副的运动几何模型； 并针对柱形面状的分度盘轮齿廓面（如渐开线柱面），讨论了其共轭曲面的形状与特征、接触线分布规律、共轭的界限条件、诱导曲率等问题，奠定了此类机构的理论基础，为分度凸轮机构装置的设计与制造提供了理论依据。
6) cams
凸轮机构
1.
The essay analyzes the stress on the follower and roller of disk cams of roller follower,studies the mechanical conditions for the roller to roll and quantitatively draws the reasonable relative parameter for the roller to roll.
本文分析了滚子直动从动件盘形凸轮机构中从动件和滚子的受力,研究了滚子作滚动的力学条件,定量地得出了凸轮机构中滚子做滚动的相关参数的合理选择。
2.
It fits willfully functions of cams follower.
分析了摆动从动件盘形凸轮机构的压力角与基本尺寸之间的关系。
3.
an developing graphical design method precise soluting The cams basic dimensions was mentioned.
对摆动从动件盘形凸轮机构的压力角与基本尺寸之间的关系进行了分析 ,提出了一种求解摆动从动件盘形凸轮机构基本尺寸的方法。
补充资料：凸凸囊囊
1.犹鼓鼓囊囊。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条