1)  air controlled dilution valve
气控稀释阀
2)  air control
气控
1.
The thesis takes ED25SH shield hauler as an example,analyses the operating principle of its air control safety circuit and summarizes its characteristics.
以ED25SH支架搬运车为例,分析了气控安全保护系统工作原理,总结了其特点。
2.
Aim at the advantages of tightness storage in basement,the air control store the grain to take the green environmental protection storing grain to maintain freshness technology, has represented this development tendency, we draw upon the professional burning facility to burn the charcoal in a cycle course to approach the target of lowering oxygen compoment in air.
针对地下仓储粮具有密封性能的先决条件,气控储粮作为一种无公害、绿色环保储粮保鲜技术,代表了这一发展趋势,通过专用的燃烧设备,将木炭燃烧循环脱氧,达到低氧气控储粮的目的。
3)  electrical control
电气控制
1.
Design of Fluid Drive and Electrical Control System for Bore Modular Machine Tool;
钻孔组合机床液压传动和电气控制系统的设计
2.
Development of the electrical control systems of RX-300 hot spinning machine;
RX-300热旋压机电气控制系统的研制
3.
Design and application of baling press electrical control system;
打包机电气控制系统的设计与应用
4)  electric control
电气控制
1.
Design of electric control on teaching and demonstrating system for engagement and disengagement device of offset press;
胶印机离合压机构示教装置的电气控制设计
2.
Signal measurement and processing in electric control of heating furnace;
加热炉电气控制中的信号检测与处理
5)  smoke control
烟气控制
1.
A performance-based design on smoke control in a large space primary of cigarette processing workshop;
大空间卷烟制丝车间烟气控制性能化设计
2.
Research on smoke control of single room-cloister-atrium;
某单室-回廊-中庭烟气控制方案研究
3.
The study on smoke control in large atrium of national museum;
国家博物馆大广场中庭烟气控制研究
6)  principle of pneumatic control
气控原理
1.
The paper expatiates on principle of pneumatic control,option for crust breaker and feeder and calculating consumption of compressed air per pot and pipe diameters.
本文介绍了打壳和定容气动装置的选择,系统气控原理,单槽压缩空气用量和管径的选择。
参考词条
补充资料:溢流阀、顺序阀、减压阀的比较
溢流阀
减压阀
顺序阀
控制油路的特点
通过调整弹簧的压力控制进油路的压力,保证进口压力恒定,p2=0
通过调整弹簧的压力控制出油口的压力,保证出口压力p2稳定
直控式-通过调定调压弹簧的压力控制进油路压力;夜控式-由单独油路控制压力
出油口情况
出油口与油箱相连
出油口与减压回路相连
出油口与工作回路相连
泄漏形式
内泄式
外泄式
内泄式
进油口状态及压力值
常态
常闭(原始状态)
常开(原始状态)
常闭(原始状态)
工作状态
进出油口相通,进油口压力为调整压力
进油口压力低于出油口压力,出油口压力稳定在调定值上
进出油口相通,进油口压力允许继续升高
联接方式
并联
串联
实现顺序动作式串联作卸荷阀用时并联
功用
定压、溢流或安全作用限压、稳压、保压
减压、稳压
不控制系统的压力,只利用系统的压力变化控制油路的通断
进油腔压力p1控制阀芯移动
出油腔压力p2控制阀芯移动
进油腔压力p1控制阀芯移动
说明:补充资料仅用于学习参考,请勿用于其它任何用途。