1) shear strength
耐剪切强度
2) shear strength
剪切强度
1.
On shear strength testing method of explosion cladding joint;
爆炸复合接头剪切强度测试方法研究
2.
Effect of magnetic field on shear strength of adhesively bonded single lap joint;
外加磁场对粘接接头剪切强度的影响
3.
Interfacial reaction and shear strength of Sn-Zn-Cu/Cu joints;
Sn-Zn-Cu/Cu界面反应及剪切强度
3) shearing strength
剪切强度
1.
The adjusted shearing strength formula of rough rock joint;
粗糙岩石节理剪切强度的修正公式
2.
Effect of rosin contents of lead-free solder paste on the shearing strength of the weld spot;
无铅焊膏中松香含量对焊点剪切强度的影响
3.
Study of the shearing strengths of marine sediment in the China’s mining region;
海底沉积物剪切强度的试验研究
4) shear bond strength
剪切强度
1.
Effect of different surface conditioning on shear bond strength of different types of luting cements to ceramics;
瓷表面不同处理方法及粘结剂对全瓷剪切强度的影响
2.
Study of shear bond strength of light-cured and resin-reinforced glass ionomer cement immediately after bonding;
光固化树脂加强型玻璃离子水门汀即刻剪切强度的测定
3.
Comparative study on the shear bond strength of light-cured glass ionomer cement between etching and nonetching;
酸蚀对树脂加强型玻璃离子抗剪切强度的影响
5) shear bonding strength
剪切强度
1.
Evaluate of shear bonding strength of a self-etching adhesive to dentine in different conditions;
牙本质表面不同状态对自酸蚀体系剪切强度影响的实验研究
2.
Objective:The aim of the study was to investigate the effects of different etching time on shear bonding strength to guide its clinical use.
目的:研究不同酸蚀时间和不同施力方向对正畸托槽与牙面间剪切强度的影响。
3.
To investigate the effects of different surface conditioning methods on the shear bonding strength of glass-infiltrated ceramic to dentine, 24 glass-infiltrated ceramic testing-pieces were divided into four groups randomly.
用Super Bond与牙本质粘接 ,测其剪切强度。
6) shear strength
抗剪切强度
1.
The effect of crystal powder on the shear strength and expansion ratio of the crystal powder/epoxy resin composite by different composition and technology was studied systematically.
对水晶粉/环氧树脂复合材料的抗剪切强度、热膨胀系数进行较系统的研究,并用扫描电镜(SEM)对水晶粉/环氧树脂复合材料断面显微结构进行了观察。
2.
Gauging the shear strength,tensile strength and modulus,glass transition temperature of the composite and their change during the aging test.
选用TDE-85和E-51作为主体树脂,制备了一种T700碳纤维复合材料,并对这种复合材料进行耐湿热老化研究,分别测定其抗剪切强度、抗拉伸强度及模量和玻璃化转变温度随老化时间的变化值。
3.
This paper briefly introduces the use of the cable bolt anchoring technology, initially analyzes the anchoring mechanism of the fully bonded cable bolt in the jointed rock mass, and examines some factors affecting the tensile bond strength and the shear strength of the cable bolt in the jointed rock mass.
简要介绍了锚索加固技术的应用，并对全长粘结式锚索在节理岩体中的锚固作用机理进行初步分析，同时对节理岩体中锚索加固的抗拉粘结强度及抗剪切强度的影响因素进行了分析。
补充资料：层间剪切强度
分子式：
CAS号：
性质：层压件和纤维增强复合材料中层与层之间的最大剪切强度。作用于面上的应力与面相平行。其值较小。如树脂为环氧体系，增强材料为玻璃纤维时，纤维方向的拉伸强度达103MPa，而层间剪切强度为40～50MPa。
CAS号：
性质：层压件和纤维增强复合材料中层与层之间的最大剪切强度。作用于面上的应力与面相平行。其值较小。如树脂为环氧体系，增强材料为玻璃纤维时，纤维方向的拉伸强度达103MPa，而层间剪切强度为40～50MPa。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条