1) tensile shear strength
拉伸剪切强度
1.
MTS-810 testing apparatus and scanning electron microscope were used to study the tensile shear strength, elongation and microstructure of epoxy construction adhesive before and after the vacuum thermal cycling.
采用MTS-810型材料试验机和扫描电子显微镜,研究了真空热循环下环氧结构胶粘剂拉伸剪切强度、延伸率和微观结构等变化规律。
2.
In this paper,the influences of curing agent,low molecular polyamide,organophilic montmorillonite and nano-Al2O3 on tensile shear strength and erosion and wear resistance of epoxy resin coating were studied,the results showed that the tensile shear strength and the erosion and wear resistance of the coating can be improved obviously with organophilic montmorillonite and nano-Al2O3.
研究了固化剂低分子聚酰胺、有机蒙脱土和纳米Al2O3的用量对环氧树脂胶粘涂层拉伸剪切强度和耐冲蚀磨损性能的影响。
2) Shear strength
拉伸剪切强度
1.
In this paper ,the effect of epoxy resin 、curing agent 、plasticizer、 coupling agent and nano-montmorillonite on shear strength was investigated through orthogonal experiment.
通过正交试验研究了环氧树脂、固化剂、增韧剂、有机化纳米蒙脱土、偶联剂对环氧胶粘剂拉伸剪切强度的影响,并对所得配方的胶粘剂进行腐蚀和冲蚀磨损试验,由此推荐环氧树脂／纳米蒙脱土胶粘剂各组分的最佳加入量。
2.
The effects of the different nanometer-fillers to the properities (Shear strength, compact, Compressive strength, wear resistance) of epoxy are also studied .
在此基础上研究不同填料对胶粘剂拉伸剪切强度、冲击弯曲强度和耐磨性的影响,推荐纳米填料环氧树脂胶粘剂最佳配方。
3.
In this paper, the effect of kind, doze and size of the filler on are studied characteristic of the epoxyadhesive coating, which is shear strength, the rate of solid particle erosion and hardness are stuied.
通过试验研究了碳化硼作为填料，其含量、粒度、对环氧胶粘涂层拉伸剪切强度、冲蚀磨损率、硬度的影响。
3) tensile shearing strength
拉伸剪切强度
1.
The effect on the tensile shearing strength of the ratio of polyether polyol to epoxy resin,the ratio of A component to B component and the surface treatment process were studied.
考查了聚醚多元醇与环氧树脂的配比,A与B组分配比及表面处理工艺对拉伸剪切强度的影响。
2.
The tensile shearing strength of anodic and cathodic epoxy electrophoretic coatings and spray epoxy painting on aluminium alloy and steel were determined according to national standard of tensile shearing strength determination method for adhesives.
借鉴国标胶粘剂拉伸剪切强度测定方法测定了阳极、阴极环氧电泳漆与环氧涂料在底材为铝合金及钢材上漆膜的拉伸剪切强度。
4) tensile-shear strength
拉伸剪切强度
1.
The laminated steel sheet is of high tensile-shear strength with high strain rate and at low temperature.
该复合钢板在20～150℃范围内具有良好的减振性能;在较低温度和较高形变速率下,复合钢板具有较高的拉伸剪切强度,在80℃附近,拉伸剪切强度最低,在80～150℃范围内,拉伸剪切强度随温度升高而增加;增加钢板表面粗糙度有利于改善复合铜板的成型
2.
10 mm, the vibration damping laminated steel sheet is of higher tensile-shear strength, its destruction show the feature of sub-interface breaking between sandwich and steel sheet.
10mm的复合钢板具有较高的拉伸剪切强度,其破坏形态为钢板与高聚物夹层间的类似界面破坏。
5) tensile strength
拉伸剪切强度
1.
Polyurethane adhesives prepared from liquefied wood has the tensile strength of 5 MPa,which meets the application requirement.
利用液化产物制备了聚氨酯胶黏剂,拉伸剪切强度达5 MPa,达到应用要求,为今后的工业化生产提供了依据。
2.
The influence of the ratio of monomers and photoinitiator on tensile strength was discussed.
本研究采用三种丙烯酸酯单体(M01、M02、M03)和一种紫外光引发剂(I01)配制了紫外光固化胶粘剂,探讨了不同原料配比对产品拉伸剪切强度的影响。
3.
The data of adhesion and tensile strength showed that the water-based CPP paint can substitute for solvent-based CPP coating.
从粘附力和拉伸剪切强度测定结果可以看出,用水性氯化聚丙烯代替溶剂型氯化聚丙烯是可行的。
6) Anti tensile shearing strength
抗拉伸剪切强度
补充资料：拉伸剪切粘接强度
分子式：
CAS号：
性质：对粘接头试片的胶层施加拉伸剪切负荷，至接头破坏的最大负荷，除以粘接面积的值。也即在平行于胶层的载荷作用下，胶接试样破坏时，单位胶接面所承受的剪切力，用MPa表示。胶黏剂的拉伸剪切强度试验还常在高温或低温条件下进行。是胶黏剂主要的胶接强度指标，许多国家都有标准试验方法。
CAS号：
性质：对粘接头试片的胶层施加拉伸剪切负荷，至接头破坏的最大负荷，除以粘接面积的值。也即在平行于胶层的载荷作用下，胶接试样破坏时，单位胶接面所承受的剪切力，用MPa表示。胶黏剂的拉伸剪切强度试验还常在高温或低温条件下进行。是胶黏剂主要的胶接强度指标，许多国家都有标准试验方法。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条