1) sulfuric-acid rubber
硫酸橡胶
2) vulcanizate
['vʌlkənizeit]
硫化橡胶
1.
Microwave Devulcanization Machanism of Sulfur-vulcanizate;
硫化橡胶微波脱硫机理的再讨论
2.
Study on Degradation Rule of Physical Mechanical Property of Vulcanizate During the Period of Heat Ageing;
硫化橡胶热氧老化时物理机械性能变质规律的研究
3.
Aging resistant is one of the properties for vulcanizate of tire tread.
轮胎胎面硫化橡胶的耐老化是其重要性能之一。
3) polysulfide
[英][,pɔli'sʌlfaid] [美][,pɑli'sʌlfaɪd]
聚硫橡胶
1.
The process and kinetics of thermal degradation in a series of polysulfide-based polyurea were studied by TG,DTA and ATR-IR.
对一系列聚硫聚氨酯(脲)的热降解进行了研究,由异佛尔酮二异氰酸酯(IPDI)、甲苯二异氰酸酯(TDI)、液体聚硫橡胶(LP)以及2,5-二氨基-3,6-二甲硫基甲苯(E300)合成聚硫聚氨酯脲,用TG、DTA、ATR-IR等研究其热降解性能。
2.
The reaction mechanism including the modification of epoxy,silicone,phenolic and polysulfide,and the performance s changes of modified polyurea were reviewed.
综述了喷涂聚脲弹性体的改性方法,重点介绍了环氧树脂、有机硅、酚醛树脂、液态聚硫橡胶改性喷涂聚脲弹性体的反应机理及改性后材料的性能变化特点。
3.
The commonly used elastic impression materials in clinic are alginate hydrocolloid impression material,agar hydrocolloid impression material,silicone impression material,polyether impression material and polysulfide impression material.
临床常用的口腔弹性印模材料有藻酸盐水胶体印模材料、琼脂水胶体印模材料、硅橡胶印模材料、聚醚橡胶印模材料和聚硫橡胶印模材料。
4) polysulfide rubber
聚硫橡胶
1.
Research on the elastic abrasive performance of the alloying system of polysulfide rubber,epoxy resin and brown corundum;
聚硫橡胶/环氧树脂/棕刚玉共混体系弹性磨具性能的研究
2.
Study on toughening of epoxy resin with polysulfide rubber;
聚硫橡胶增韧环氧树脂研究
3.
Effect on toughening epoxy adhesive with polysulfide rubber
聚硫橡胶对环氧胶粘剂的增韧作用研究
5) thiokol rubber
聚硫橡胶
1.
One method to improve efficiently polyaniline's electrochemical catalysis and anti corrosion performance is to coelectropolymerize polyaniline and thiokol rubber in the non aqueous solution.
利用循环伏安、交流阻抗和动电位扫描 ,研究了聚苯胺 /聚硫橡胶复合修饰电极在半胱氨酸的硫酸溶液中对含有 S— S键的电化学反应的电催化作用及复合膜对碳钢的防腐作用和它本身的稳定性 。
2.
A series of polyaniline/thiokol rubber(PAn/TR)composite films has been prepared by electrochemical polymerization in one_step process in the solutions containing aniline and thiokol rubber prepolymer.
以苯胺、聚硫橡胶预聚体为主要原料，采用电化学一步法原位复合，制备了聚苯胺／聚硫橡胶复合膜。
3.
A novel class of conducting polypyrrole/thiokol rubber composite films were prepared by electrochemistry via one step process from the MeCN solution containing thiokol rubber with electronic active group(SH), pyrrole and trichloroacetic acid(TCA).
利用带有电活性端基（－ＳＨ）的液体聚硫橡胶与吡咯单体在以三氯乙酸（ＴＣＡ）作增溶剂兼支持电解质的乙腈溶液中一步电化学氧化复合，制备了一类新型的聚吡咯／聚硫橡胶导电复合膜。
6) rubber vulcanization
橡胶硫化
1.
As the existent vulcanization jar multiprocessing control system is enormous,the deployed wires are complex, and the control precision is very low, a rubber vulcanization intelligent multiprocessing control system based on fieldbus is designed, adopting advanced immune fuzzy PID control method.
针对目前橡胶硫化罐群控系统规模大,布线复杂,控制精度低等问题,设计了一套以现场总线技术为基础,采用先进的免疫模糊PID控制的橡胶硫化罐现场总线群控系统。
2.
Key-process of producing damping belt-drive pulley is rubber vulcanization.
橡胶硫化是减振输送带轮生产的关键工艺,决定了输送带轮的寿命和可靠性。
补充资料：橡胶模具、橡胶压模、橡胶硫化模
分子式：
CAS号：
性质：又称橡胶模具、橡胶压模、橡胶硫化模。用于压制橡胶产品的金属模型。一般用钢材(如45号钢)按图纸要求经机械加工而制得，并经热处理以提高其硬度及耐磨性。模具型腔与产品结构相同，型腔尺寸必须考虑不同橡胶的收缩率，在产品尺寸基础上进行放大或缩小，方可得到合适的产品尺寸。模具从工艺操作考虑还要设置流胶槽、启模口、定位销等。
CAS号：
性质：又称橡胶模具、橡胶压模、橡胶硫化模。用于压制橡胶产品的金属模型。一般用钢材(如45号钢)按图纸要求经机械加工而制得，并经热处理以提高其硬度及耐磨性。模具型腔与产品结构相同，型腔尺寸必须考虑不同橡胶的收缩率，在产品尺寸基础上进行放大或缩小，方可得到合适的产品尺寸。模具从工艺操作考虑还要设置流胶槽、启模口、定位销等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条