1) single size parallel clamp
均一尺寸平行夹具
3) average size
平均尺寸
1.
Surface morphology of the Si film was observed by scanning electron microscopy(SEM) and was found that the average size of Si nanoparticles prepared in different gas all increased initially and then decreased with distance between the target and the substrate increasing.
利用扫描电子显微镜(SEM)观察样品的表面形貌,并对晶粒尺寸进行统计分析,发现不同环境气体下,纳米Si晶粒平均尺寸均随衬底与靶的距离增加有着先增大后减小的规律;通过分析比较,同等条件下Ne气环境下制备的纳米Si晶粒平均尺寸最小。
2.
The average size estimation is an important way to control production quality in many fields, however, the method of traditional measurement by hand is very difficult to meet to the continual mechanized manufacture.
平均尺寸的检测在很多领域都是产品质量控制的重要手段，然而传统的手工测量方法很难适应于连续机械化生产的需要。
4) single-size material
尺寸均一的材料
5) single-size material; one-size material
均一尺寸材料
6) average grain size
平均晶粒尺寸
1.
Nondestructive evaluation of average grain size of coarse grain materials based on ultrasonic transmissive technique;
超声波透射技术无损评价粗晶材料平均晶粒尺寸
2.
The influence of current density on the microstructure such as average grain size and texture of Ni coatings was studied as well.
当电流密度从45A/dm2增加到120A/dm2时,镀层平均晶粒尺寸逐渐减小;而进一步增加电流密度到180A/dm2,镀层晶粒尺寸又会有轻微的增大。
3.
The average grain size and microstructure of the nickel nanocoatings heated at different temperature for 2 h and Ni/carbon nanotube composite nanocoatings were examined by X-ray diffractometer(XRD),and their wear behaviour and microhardness were investigated.
用含碳纳米管的快速镍电刷镀液制备了镍/碳纳米管复合纳米镀层,研究了热处理温度和镀液中碳纳米管含量对镀层平均晶粒尺寸、结构、力学性能及耐磨性能的影响。
补充资料：工程图标准尺寸及坐标尺寸
标准标注类型，是我们常用的标注类型。而坐标标注是便于数控加工采用的另一中标注形式。PRO/E可以将两种标注方式进行转换。
· 3.2 标准标注到坐标标注的转换
注意： 转化为坐标标注的尺寸必须是线性标注的，下列尺寸不能转化为坐标标注：
- 被显示成线性尺寸的直径
- 中心线尺寸
- 选择MODIFY DRAW > Dim Params > Dim Type > Ordinate Dim > Create Base.
- 选择作为参考基准线的尺寸
- 选择基准的引出线，该点为0点
- 选择 MOD DIM TYPE > Lin to Ord .
- 选择线性尺寸：注意：必须选择具有相同基准的尺寸
========>>>>
1. 选择 DIM PARAMS > Diam Dim Type .
2.点击Ord to Lin 
3.选择尺寸即可
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条