1) radial serrations
径向齿纹
2) plunge shaving
径向剃齿
1.
The tooth flank equations of plunge shaving cutter and conventional shaving cutter are deduced using the engagement principle for single freedom and two freedom respectively.
从齿轮啮合原理入手 ,导出了单自由度的径向剃齿刀的齿面方程 ,与双自由度的普通剃齿刀齿面方程 ;分析并阐述了径向剃齿法与普通剃齿法在啮合原理上的区别 ;通过对相同参数条件下径向剃齿刀和普通剃齿刀的比较 ,得出了若干结论 ,为径向剃齿刀的设计提供了理论依
2.
Plunge shaving is one of the most effective technologies for gear finishing, but it is difficult to profile plunge shaving-cutter.
径向剃齿是一种高效的齿轮精加工方法，但径向剃齿刀的修磨比较困难。
3.
Shaving is one of the most widely used methods for finishing gear teeth,and the plunge shaving method is a more efficient process for finishing gear teeth.
剃齿加工是齿轮精加工的一种工艺方法,而径向剃齿法是剃齿工艺中一种更加高效的齿轮精加工工艺。
3) radial pick
径向截齿
4) radial crack
径向裂纹
1.
Influence of radial crack on vibrational frequencies of thin circular plate clamped on edge;
径向裂纹对周界固定薄圆板振动频率的影响
5) plunge shaving cutter
径向剃齿刀
1.
The tooth flank equations of plunge shaving cutter and conventional shaving cutter are deduced using the engagement principle for single freedom and two freedom respectively.
从齿轮啮合原理入手 ,导出了单自由度的径向剃齿刀的齿面方程 ,与双自由度的普通剃齿刀齿面方程 ;分析并阐述了径向剃齿法与普通剃齿法在啮合原理上的区别 ;通过对相同参数条件下径向剃齿刀和普通剃齿刀的比较 ,得出了若干结论 ,为径向剃齿刀的设计提供了理论依
2.
Based on the one to one correspondence of the points on the tooth trace of plunge shaving cutter and the shaved gear, a method used to calculate the axial modification of the plunge shaving cutter when processing a crown gear is proposed.
根据径向剃齿刀与被剃齿轮间存在的一一对应关系，提出一种加工鼓形齿时径向剃齿刀修形量的计算方法。
3.
Using the profile equation of plunge shaving cutter deduced from the gear engagement theory for one degree of freedom, a method used to calculate the minimum width of a plunge shaving cutter is presented.
在利用单自由度啮合原理推导出径向剃齿刀齿面方程的基础上，提出了一种径向剃齿刀最小宽度求解方法。
6) radial gear shaving cutter
径向剃齿刀
1.
the calculating formula of the tooth number of the radial gear shaving cutter is presented.
介绍了径向剃齿刀的设计方法及其技术参数的确定。
补充资料：齿（齿所）
齿（齿所）
齿（齿所） 病名。系指牙齿被醋浸渍的病证。《诸病源候论》卷二十九：“齿（齿所），齿伤酢也。齿者骨之所终，髓之所养，髓弱骨虚，风气客之，则齿（齿所）。”酢，同醋。参见齿齼条。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条