1)  alkaline wash-off
碱性清洗
2)  caustic dip
碱性清洗
3)  alkaline
碱性
1.
A process of non-cyanide alkaline copper plating;
无氰碱性镀铜清洁生产工艺的研究
2.
Study of zinc-iron-titanium dioxide composite plating in alkaline zincate bath;
碱性锌酸盐体系锌-铁-二氧化钛复合电镀工艺的研究
4)  alkalinity
碱性
1.
Raising copple agelimit of alkalinity medium frequency induction furnace;
提高碱性中频感应电炉的坩埚寿命
2.
The sorts and alkalinity of basic ionic liquids could be designed and adjusted through molecular design.
对近年来具有碱性的离子液体的研究进行综述,指出碱性离子液体既具有离子液体的特性,又具备作为碱性催化剂的前景。
3.
This paper describes the three factors that affect the alkalinity of the compounds containing nitrogen and gives the method that adjusts the alkalinity of these compounds, furthermore, the paper also provides new and reasonable explanations to some results.
本文讨论了影响含氮化合物碱性的三方面因素，根据实际特例说明了判断化合物碱性的方法，并对一些结果作出新的且合理的解释。
5)  alkali
碱性
1.
Influence of alkali condition on removing Na of NaY molecular sieve and its structure;
碱性条件对NaY分子筛脱钠及其结构的影响
2.
Stability of aluminum in alkaline solution containing lithium salt;
铝在含锂盐的碱性溶液中稳定性的研究
3.
The present paper reviews functions of tundish covering agent in continuous casting and explains systematically the characteristics of various covering agents with different functions used for various steels and points out that the difficult problem in researching the covering agent assumes to be temperature holding of the tundish covering agent for the carbon free alkali tundish.
系统综述连铸中包覆盖剂的作用,不同钢种、不同功能覆盖剂的特点,指出覆盖剂的研究难点是无碳碱性中包覆盖剂的保温问题。
6)  Basicity
碱性
1.
The basicity of amine and the factor of its influence;
胺的碱性强弱及其影响因素
2.
Basicity of Ba-La -O-(F) Catalysts and Their Catalytic Performances for the OCM Reaction;
Ba-La-O-(F)催化剂的碱性及其OCM反应性能
3.
The results of calculation show that in the basicity, the reaction channel has one five-membered ring transition state TS1, with the activation energy of the controlling step during the reaction of 25.
结果表明:在碱性条件下,水解反应主要经历一个五元环的过渡态TS1,该反应速控步骤的能垒为25。
参考词条
补充资料：48892清洗机操作规程
1、遵守铸造设备通用操作规程。
2、工作前还必须遵守：
a、检查管路系统有无漏气漏水的情况，如有这种情况，应通知维修人员修理。
b、检查清洗液是否足够，如果不够，及时增加清洗液。
c、先点动试车，然后空运转2-3分钟，检查传动系统（电动机、联轴节、减速器）和运输带的运动是否平稳，确认一切正常后，方可进行生产。
3、工作中还必须遵守：
a、被清洗的零件要整齐地放在运输带上，不许压在滚轮上；
b、在运输带上，被清洗的零件不能堆得过多，以免影响清洗效果。
c、工作后，被清洗的零件不能停放在运输带上。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。