1) annealing for optical homogeneity
光学均匀性退火
2) annealing uniformity
退火均匀性
1.
The influence on the surface morphology and the annealing uniformity of the films was discussed by adjusting different annealing parameters.
讨论了激光退火工艺参量对镱铒共掺Al2O3薄膜表面形貌和退火均匀性的影响。
3) optical homogeneity
光学均匀性
1.
Testing the optical homogeneity of an optical glass block layer by layer according to the interference principle of dual surfaces of the liquid;
用双液面干涉法层析光学玻璃的光学均匀性
2.
The results show that a thermal annealing at the proper temperature of experiments can significantly improve the optical homogeneity of the crystals,especially for the crystal grown at a rapid speed.
结果表明,适当温度的退火处理能有效地提高晶体的光学均匀性,尤其是对快速生长的晶体质量提高更为显著。
3.
Zn,Mg∶ LiNbO_3 crystal was grown by the pulling method from the melt and its composition,growth,optical homogeneity,photo-refraction resistance and frequency doubling were investigated.
为了研制出结合Zn∶L iNbO3与Mg∶L iNbO3优点的晶体,采用提拉法从熔体中生长了Zn,Mg∶L iNbO3晶体,并对它的配方和生长性能、光学均匀性、抗光折变以及倍频性能进行了研究,生长出了尺寸达40mm×70mm、双折射率梯度优于10-4/cm量级的Zn,Mg∶L iNbO3晶体,倍频得到了20m J的0。
4) light uniformity
光学均匀性
1.
The results of optical experiment show that the characteristics of light uniformity depend greatly on the concentrations of quaternary ammonium salt in solution.
透过率特性的实验结果表明 ,不同浓度的季氨盐对 KDP晶体的光学均匀性有较大影响。
5) Homogeneity
[英][,hɔmədʒə'ni:əti] [美]['hɑmədʒə'niətɪ]
光学均匀性
1.
Measurement of Homogeneity of Optical Glass with Parallel Surfaces Using Low Coherence Light Sources;
用短相干光源测量平行平板玻璃的光学均匀性
6) homogenization
[,həʊmədʒənaɪ'zeɪʃən]
均匀化退火
1.
Influence of homogenization on flow stress of Al-1Mn-1Mg alloy during hot compression deformation;
均匀化退火对Al-1Mn-1Mg合金高温压缩流变应力的影响
2.
Influence of homogenization on morphologies of the precipitated phases in Al-1Mn-1Mg alloy;
均匀化退火对Al-1Mn-1Mg合金中析出相形态的影响
3.
Influence of melt-treatment and homogenization on microstructure and mechanical properties has been studied systematically and deeply with the aids of some modern .
借助光学显微镜(OM)、扫描电镜(SEM)、透射电镜(TEM)、能谱仪(EDAX)、X射线衍射(X-Ray)、电子拉伸机等先进的分析测试手段,系统深入地研究熔体处理与均匀化退火工艺对易拉罐用铝材微观组织与力学性能的影响规律,在此基础上采用动态热/力模拟试验技术,全面深入地探讨了易拉罐用铝材的熔体处理、热处理工艺、热塑性变形行为三者之间的相互关系,深化了对铝熔体处理的基本理论、冶金缺陷的作用机理以及铝材高温塑性变形理论的认识,对进一步挖掘易拉罐用铝材的性能潜力具有重要意义,可为实际热轧工艺的确定和优化提供试验依据与理论指导。
补充资料:软化退火(见低温退火)
软化退火(见低温退火)
soft-annealing
rU0nhUO tUihUO软化退火(soft一annealing)见低温退火。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条