1) circuit protection valve
电路保护阀
2) valve short circuit protection
阀短路保护
1.
This paper studies the influence of converter transformer D-bridge zero sequence circulating current on valve short circuit protection.
笔者研究了换流阀三角形侧零序环流对阀短路保护误动作的影响。
3) protecting circuit
保护电路
1.
Analysis on hardware of transmission based computer HD325-5 model dump truck for power supply protecting circuit;
HD325—5型工程自卸车速度控制计算机硬件过流过压和电源保护电路剖析
2.
According to the requirements of electrochemical micromachining,an adjustable pulsed power supply unit is developed by using the μs-grade adjustable pulsed generating circuit,main circuit of pulsed power supply and protecting circuit which are controlled by single chip microcomputer.
根据微细电解加工的要求,应用单片机控制的微秒级可调脉冲发生电路、脉冲电源主电路和保护电路,研制了可调脉冲电源装置。
3.
This paper analyses the composing of power protecting circuit and steady voltage circuit in KOMATSU model HD460 dump truck.
分析了日本KOMATSU(小松 )公司HD4 6 0大型工程自卸车速度控制计算机电源保护电路与稳压电路的构成。
4) protection circuit
保护电路
1.
Improvement of main thyristor s protection circuit of XHD150B-1O 800mA X-ray machine;
800mAX线机主可控硅损坏保护电路的改进研究
2.
Design of short-circuit protection circuit for Li-ion battery piles;
锂离子电池组的短路保护电路设计
3.
High power IGBT drive and protection circuit;
一种大功率IGBT实用驱动及保护电路
5) circuit protection
电路保护
6) protective circuit
保护电路
1.
The design and study of IGBT short circuiting protective circuit;
IGBT 短路保护电路设计与研究
2.
Novel protective circuits of diode laser;
新型的半导体激光器保护电路
3.
Using non-polluting cold-producing medium R134a and devising the protective circuit of ammeter and power factor meter with time delay relay,it improved the properties of the refrigeration cycle instrument.
研制了创新型制冷循环综合实验仪,使用了R134a绿色环保型制冷剂,改进了制冷循环系统,采用延时继电器设计了电流表和功率因数表的保护电路。
补充资料:溢流阀、顺序阀、减压阀的比较
溢流阀 | 减压阀 | 顺序阀 | ||
控制油路的特点 | 通过调整弹簧的压力控制进油路的压力,保证进口压力恒定,p2=0 | 通过调整弹簧的压力控制出油口的压力,保证出口压力p2稳定 | 直控式-通过调定调压弹簧的压力控制进油路压力;夜控式-由单独油路控制压力 | |
出油口情况 | 出油口与油箱相连 | 出油口与减压回路相连 | 出油口与工作回路相连 | |
泄漏形式 | 内泄式 | 外泄式 | 内泄式 | |
进油口状态及压力值 | 常态 | 常闭(原始状态) | 常开(原始状态) | 常闭(原始状态) |
工作状态 | 进出油口相通,进油口压力为调整压力 | 进油口压力低于出油口压力,出油口压力稳定在调定值上 | 进出油口相通,进油口压力允许继续升高 | |
联接方式 | 并联 | 串联 | 实现顺序动作式串联作卸荷阀用时并联 | |
功用 | 定压、溢流或安全作用限压、稳压、保压 | 减压、稳压 | 不控制系统的压力,只利用系统的压力变化控制油路的通断 | |
进油腔压力p1控制阀芯移动 | 出油腔压力p2控制阀芯移动 | 进油腔压力p1控制阀芯移动 |
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条