2) low melting point
低熔点
1.
The low melting point Ga-Ag-Sn liquid state alloy prepared by vacuum melting method was studied.
采用真空冶炼法制备了低熔点的Ga-Ag-Sn液态合金,分析了Ga含量与液态合金熔点的关系。
2.
Influences of low melting point and semi - crystalline EVA on the structure, conductive behavior and positive temperature coefficient (PTC) of PS-HI/CB system were studied by means of XRD, DSC and SEM.
采用XRD、DSC、SEM等研究了低熔点、半结晶聚合物EVA对非晶聚合物高抗冲聚苯乙烯／炭黑(PS-HI／ CB)复合材料的结构、导电性和正温度系数(PTC)效应的影响,结果表明,EVA,可提高复合材料的PTC强度,当PS- HI/EVA/CB=70:30:30时复合材料的PTC强度由不加EVA的2。
3.
By employing the melt-spinning technique, an alloy, which used to be brittle, was made into a highly tough alloy-strip, and the low melting point of which was maintained.
采用熔体急冷新技术使原来呈脆性的低熔点合金被加工成高韧性的条带。
3) lower melting point
低熔点
1.
The results indicated the bismaleimide showed lower melting point which had decreased 39℃ because of methyl side-group.
通过甲基对苯二酚和对马来酰亚胺基苯甲酸,制得了一种低熔点的酯类液晶双马来酰亚胺。
2.
This paper discusses the technical requirements mierocrystal sealing lass-ceramics with lower melting point nd the matching sealing conditions of sealed pieces.
探讨低熔点微晶封接玻璃的技术要求和封接件的匹配封接条件，并给出部分低熔点微晶封接玻璃的性质和典型封接工艺。
4) low-melting point
低熔点
1.
Study on composite spinning process for low-melting point polyester;
低熔点聚酯复合纺丝研究
5) decreasing melting point
降低熔点
6) eutectic point
低共熔点
1.
The experimental results showed:NaSCN-NaAc--NaI ternary system is of the eutectic type,and the eutectic point is located at 504 K and consists of 19.
用目测变温法研究了ＮａＳＣＮ－ＮａＡｃ－ＮａＩ三元系的相图，结果表明：ＮａＳＣＮ－ＮａＡｃ－ＮａＩ三元体系为低共熔型相图，它的低共熔点的温度为５０４Ｋ，组成为（ｍ％）：ＮａＩ（１９。
补充资料：低屈服点钢
分子式：
CAS号：
性质： 屈服点相对较低的钢。这种钢具有优良的深冲性能和深拉延性能，容易变形加工制造形状复杂的钢制品。典型的低屈服点钢如08F钢，它的屈服点只有176MPa左右，在各类钢中其屈服点显著偏低。用这种钢的薄板可制造深冲压和深拉延的制品，如各种贮器，搪瓷制品、仪表板以及管件等。
CAS号：
性质： 屈服点相对较低的钢。这种钢具有优良的深冲性能和深拉延性能，容易变形加工制造形状复杂的钢制品。典型的低屈服点钢如08F钢，它的屈服点只有176MPa左右，在各类钢中其屈服点显著偏低。用这种钢的薄板可制造深冲压和深拉延的制品，如各种贮器，搪瓷制品、仪表板以及管件等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条