说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 部件状态信息
1)  unit status information
部件状态信息
2)  partial CSI
部分状态信息
3)  partial channel state information
部分信道状态信息
1.
Simplified power allocation algorithm for MIMO systems with partial channel state information
部分信道状态信息下简化的MIMO功率分配算法
4)  Condition information
状态信息
1.
Study on conditional residual life modeling based on condition information;
基于状态信息的条件剩余寿命建模研究
5)  information status
信息状态
1.
A 2(information status: new,given) × 2(accent pattern: accented,deaccented) with-in subjects design was used.
考察新旧信息和重音之间的匹配关系对口语理解的影响,实验采用2(信息状态:新信息与旧信息)×2(重读方式:重读与不重读)被试内设计。
2.
The paper analyses the information statuses and textual functions of preposed and left-dislocated themes in Ailing Zhang s novels and short stories.
本文以张爱玲小说的对话中存在的前置主位和左移动主位的信息状态和语篇功能为切入点,分析了汉语中的前置主位和左移动主位的信息状态和语篇功能,并与英语进行对比。
3.
The structures and information status of English and Chinese inversion are compared and contrasted.
论述、对比英汉倒装的结构和信息状态差异,进一步支持Bimer和徐盛桓有关英语倒装句的信息分布理论——前置成分不应新于后置成分。
6)  information state
信息状态
1.
By introducing information state, the output feedback policy for such system was obtained.
通过引入信息状态概念来获得输出反馈控制律,对于状态和输出(测量)噪声带有一般相关系数的随机系统,推导求得了其显式的信息状态表达式。
2.
The change of information state during the process of Information Architecture and the characteristics and tendencies of different information aggregate are discussed.
论文研究了信息构建过程中信息状态的变化 ,建立了信息状态的变化模型 ,对各种信息集合的信息构建特征和发展趋势进行了探
补充资料:将UG里的一个装配部件输出成单个部件文件
法一:
  • 关闭(turn off)FileàOptions->Load Options下"Partial Loading "选项
  • 打开装配部件
  • 选择File->Export->Part
  • 在"Part Specification"下选择"new"
  • 选择"Specify Part",指定输出部件文件名称及位置
  • 将"Object Selection Scope"设定为"All Objects"
  • 选择"Class Selection->Select All"高亮所有对象
  • 按"OK"

该种方法特点:每一个部件的特征都会汇集在新部件的MNT里。可以方便编辑。

法二:

  • 闭(turn off)File->Options->Load Options下"Partial Loading "选项
  • 打开装配部件
  • Application->Assembly
  • Assemblies->Components->Create New,给出想要输出的部件文件名及路径。
  • 如下图1,在ANT上双击新产生的部件文件,使其成为工作部件。
  • Assemblies->WAVE Geometry Linker,将设置改为"Body",选择所有组件的体。
  • 将"Create Non-associative"开关设为"On",见下图2
  • 将产生的部件设成显示部件,仅保存刚产生的新部件,不保存旧的装配部件。

图1

图2

该种方法特点:每一个部件在新部件的MNT里只会显示一个link的特征。没有相应特征可以编辑。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条