1) liquid phase loading
固定液配比
2) stationary partition liquid
固定分配液
3) solid-to-liquid ratio
固液比
1.
The effects of temperature, dialogite-to-sulfuric acid ratio, and solid-to-liquid ratio on leaching of dialogite by sulfuric acid were researched in the leaching experiment of ores from Hubei.
通过对湖北矿的浸取试验研究,讨论了温度、矿酸比、固液比对菱锰矿硫酸浸取的影响,优化了浸取条件,并确定温度对浸取的影响最为显著,使浸取率可以达到99。
2.
Solid-to-liquid ratio is introduced to estimate the solid-like of microstructure.
为揭示超薄膜的摩擦特性与微观结构的关系,运用分子动力学模拟的方法对其进行研究,采用固液比作为流体膜固化的定量描述,分别讨论温度、分子层数对固液比和摩擦力的影响。
3.
The result shows that the properties of geopolymer are the best when the containing of metakaolin in the solid phase is 25%,the containing of water glass in the liquid phase is 65%,solid-to-liquid ratio is 3.
结果表明:当偏高岭石占固相含量为25%,水玻璃占液相的含量为65%,固液比为3。
4) solid-to-solution ratio
固/液比
1.
The influence of solid-to-solution ratio(SSR) on the sorption and desorption of dissolved petroleum hydrocarbons(DPH) to two surface soils(agricultural and black) was evaluated by batch reactor experiments.
采用批实验的方法,研究了2种土壤在不同的固/液比(solid-to-solution ratio,SSR)条件下对溶解性石油烃(DPH)的吸附-解吸特性。
5) Liquid-to-solid ratio (L/S)
液固比
1.
TCLP experiment has been performed to study the relationships between liquid-to-solid ratio (L/S), initial pH value, extraction time and leaching characteristics of heavy metals (Pb, Cr, Cd, Ni, Cu, Zn) in fly ash from a coal and MSW(municipal solid waste) co-firing fluidized bed incinerator.
对用流化床焚烧炉混烧垃圾和煤的布袋飞灰进行了重金属的TCLP(ToxicityCharacteristicLeachingProcedure)浸出特性实验,探讨了液固比、初始pH值及浸出时间对飞灰中重金属Pb、Cr、Cd、Ni、Cu、Zn的浸出影响。
6) liquid-solid ratio
液固比
1.
For a heap leaching operation,the liquid-solid ratio is an important parameter for calculating the leaching solution consumption,estimating the leachant concentration and designing the post-leaching processing facilities.
堆浸作业中的液固比是计算总需水量（溶浸液量）大小、估计溶浸液浓度和设计浸出液后处理设施的依据。
2.
The technique of leaching at a low liquid-solid ratio first and then leaching at high liquid-solid ratio was better than leaching at high liquid-solid ratio continuously,the recovery of cobalt was 98.
采用先低液固比再高液固比浸出的方法,效果优于传统的连续高液固比浸出,钴的总浸出率约为98。
补充资料：固定液配比
分子式：
CAS号：
性质：又称固定液配比。指气液色谱中载体表面所能承受固定液的量，其大小取决于载体的表面结构，如比表面积和孔容等。液相载荷量一般用固定液占填料总重量百分比或固定液与载体重量百分比表示。
CAS号：
性质：又称固定液配比。指气液色谱中载体表面所能承受固定液的量，其大小取决于载体的表面结构，如比表面积和孔容等。液相载荷量一般用固定液占填料总重量百分比或固定液与载体重量百分比表示。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条