1) carbon whisker
碳晶须
2) CaCO3 whisker
碳酸钙晶须
1.
In this paper,the change of filled paper property is studied with aragonite CaCO3 whisker.
文章采用自制文石型碳酸钙晶须替代传统方解石型碳酸钙,研究其填充纸张性能的变化,结果表明:同样条件下,文石型碳酸钙晶须较传统方解石型碳酸钙填料有更高的留着率,更小的纸张强度降低率。
3) silicon carbide whisker
碳化硅晶须
1.
The key process parameters for the double-heating synthesis of silicon carbide whiskers with carbon black and SiO2 powders as raw materials are studied.
双重加热法是低成本、大批量合成碳化硅晶须的新技术,合成温度低、合成时间短、生成率高。
2.
The heat conductive silicone rubber with vinyl endblocked polymethylsiloxane as basic gum and silicone nitride(Si_3N_4) of different particle sizes and silicon carbide whisker as fillers was prepared.
以甲基乙烯基硅橡胶为基胶,选用不同粒径氮化硅粒子和碳化硅晶须为填料制备了导热硅橡胶。
3.
The silicon carbide whiskers and platelets are ideal reinforcements of compound materials of ceramic,metal and resin.
碳化硅晶须和晶片都是陶瓷基、金属基、树脂基复合材料的理想增强体,与碳化硅晶须相比,有关碳化硅晶片制备与应用的报道相对较少。
4) titanium carbide whiskers
碳化钛晶须
5) silicon carbide whiskers
碳化硅晶须
1.
All kinds of approach and the mechanism to synthesize silicon carbide whiskers are commented on , and the progress of silicon carbide whiskers at home and abroad is also reviewed.
比较详细地介绍了当前国内外碳化硅晶须的生长机理与制备方法，简要评述了对碳化 硅晶须研究的进展状况。
2.
Carbon nanotubes (CNTs) and silicon carbide whiskers (SiCw) are promising reinforcement materials for manufacturing metal or ceramic based composites.
在制备复合材料中,碳纳米管和碳化硅晶须易受到空气和基体材料侵蚀而失效。
6) SiC Whiskers
碳化硅晶须
1.
The growth of SiC whiskers by in-situ on the surface of SiC foam ceramics;
泡沫碳化硅陶瓷表面原位生长碳化硅晶须
2.
Using silica micro-powder,quartz sand and kaolin as raw material of silicon,graphite with different particle size as raw material of carbon,Fe2O3、H3BO3 and NaCl as catalyst,SiC whiskers were synthesized by the carbothermal reduction reaction.
分别以SiO2微粉、石英砂和高岭土为硅源,用不同粒度的石墨为碳源,Fe2O3、H3BO3和NaCl作为催化剂,采用碳热还原法制备了碳化硅晶须。
3.
The dispersion of carbon black in silica sol and SiC whiskers synthesized by sol-gel method were studied.
本文研究了炭黑在硅溶胶中的分散以及溶胶-凝胶法制备了碳化硅晶须,同时也研究炭黑在酚醛树脂中的分散及各种改性树脂的制备,探讨了改性树脂对低碳镁碳砖性能的影响。
补充资料：碳晶须
分子式：
CAS号：
性质：一种非金属晶须。含碳量99％以上的碳针状单晶，直径5～60μm，长度4至几十厘米，密度2g/cm3以上，强度0.7～3.4GPa，模量294～412GPa，伸长率0.2％～0.8％，耐热性好。制法是以二茂铁为催化剂、氢为载体气、苯为碳素源，在1000～1150℃的管式反应炉内进行气相成长，每分钟约4～5cm长。用作树脂基和碳基复合材料增强体。
CAS号：
性质：一种非金属晶须。含碳量99％以上的碳针状单晶，直径5～60μm，长度4至几十厘米，密度2g/cm3以上，强度0.7～3.4GPa，模量294～412GPa，伸长率0.2％～0.8％，耐热性好。制法是以二茂铁为催化剂、氢为载体气、苯为碳素源，在1000～1150℃的管式反应炉内进行气相成长，每分钟约4～5cm长。用作树脂基和碳基复合材料增强体。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条