1) injected freezing gum
注凝胶
1.
The Haizhou District took synthetic measures such as the fire area outer circle block up to leak, close to injected nitrogen, injected freezing gum etc.
海州区采用火区外围堵漏、封闭注氮、注凝胶等综合灭火措施,扑灭了3312放顶煤工作灭火区,火区封闭后,又采用开放注氮、注沙段,注高水黄泥胶等综合防火措施,抑制了火区的复燃。
2) Gel casting
凝胶注模
1.
The inhibition of oxygen,which occurred in gel casting during the formation of polymer networks through in-situ polymerization of monomers in air,was successfully prevented by adding a proper amount of polyethylene glycol(PEG) to the pre-aqueous acrylamide solution.
采用凝胶注模工艺制备Al2O3陶瓷过程中,在单体和交联剂的预混溶液中加入适量的聚乙二醇(PEG),能有效克服单体聚合的氧阻聚问题,从而消除陶瓷坯体的表面起皮现象。
2.
In this paper, process of the gel casting dosage of the organic material and the primary conditions control are interviewed, and advantages of the gel casting are enumerated.
系统地叙述了凝胶注模成型工艺的工艺过程、主要用料和工艺过程中一些关键条件的控制,对其工艺特点进行了说明,并在多方面与其它几种常用的成型方法进行比较;简单介绍了微波介质陶瓷的发展过程和成型工艺的研究现状;详细分析了凝胶注模成型工艺的成型原理和将其应用于微波介质陶瓷领域的优势,并对其应用前景进行了展望。
3.
The influence factors of gel casting ZTA green body are investigated.
通过测量含不同种类和质量分数粉末浆料的粘度,坯体的密度和线性收缩率,研究了用凝胶注模成型的ZTA陶瓷坯体的影响因素。
3) gel-casting
凝胶注模
1.
Research and Development of Gel-casting;
凝胶注模成形技术的研究与发展
2.
Structure and token of alumina by gel-casting;
凝胶注模氧化铝陶瓷坯体的结构与表征
3.
The Primary Investigation of Using β-Si_3N_4 in Aqueous Gel-casting;
β-Si_3N_4的凝胶注模成型技术初探
4) gelcasting
凝胶浇注
1.
The forming processes of gelcasting,the microstructure of green bodies and the properties of zirconia ceramics were studied.
主要研究了氧化锆陶瓷的凝胶浇注成型工艺,以及坯体的微观结构和烧成后陶瓷的力学性能,并讨论获得高性能的原因。
2.
2)O_(2-y),TSDC)powders doped with 0～15% mol percents of TiO_2 were prepared by the gelcasting process.
通过凝胶浇注法制备了 TiO_2掺杂量为0～15% (摩尔分数)的 TiO_2-Ce_(0。
5) gelcasting
凝胶注模
1.
The Research and Application of Gelcasting Technology for Ceramics;
陶瓷凝胶注模成型技术及其应用研究
2.
Preparation of mesocarbon microbeads-base (MCMB) bipolar plate for proton exchange membrane fuel cell by gelcasting;
凝胶注模法制备质子交换膜燃料电池双极板
3.
Alumina ceramics prepared by aqueous gelcasting with N-methylolacrylamide system;
N-羟甲基丙烯酰胺体系凝胶注模成型氧化铝陶瓷
6) gel-casting
凝胶浇注
1.
The green bodies of carbon nanotubes/hydroxyapatite(CNTs/HA) composite were prepared by gel-casting process.
采用凝胶浇注成型工艺制备了纳米碳管/羟基磷灰石复合材料坯体。
2.
9)(DCO) powders were prepared by a modified gel-casting process withorganism aided.
以硝酸盐为原料,采用有机物辅助的水基凝胶浇注(Gel-casting)工艺合成出了Gd_(0。
补充资料：Sds-聚丙烯酰胺凝胶电泳凝胶电泳
sds-聚丙烯酰胺凝胶电泳（sds-page，sodium dodecyl sulfate-polyacrylamide gel electrohoresis）
在有去污剂十二烷基硫酸钠存在下的聚丙烯酰胺凝胶电泳。sds-page只是按照分子大小分离的，而不是根据分子所带的电荷和大小分离的。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条