1) gelcasting
凝胶注模成形
1.
Research on non-aqueous gelcasting process with high-nitrogn low-nickel stainless steel powder
非水基凝胶注模成形高氮无镍不锈钢粉末的研究
2.
Big and complex-shaped porous titanium implants prepared by gelcasting,with porosity of 46.
采用凝胶注模成形工艺制备了大尺寸、复杂形状医用多孔钛植入材料,其孔隙度为46。
3.
Gelcasting of 316L stainless steel powders was discussed in the study.
本文对316L不锈钢粉的凝胶注模成形工艺进行了研究,分析了影响浆料流变性和凝胶化时间的因素,以及单体含量对固化胶体性状的影响。
2) gelcasting
凝胶浇注成形
1.
Preparing and gelcasting of high concentrated titanium carbide suspension;
高固相含量碳化钛悬浮体的制备和凝胶浇注成形
3) Gelcasting
凝胶注模成型
1.
Effects of process parameters on the gelcasting green strength and sintered density of stainless steel;
工艺参数对凝胶注模成型不锈钢坯体强度和烧结密度的影响
2.
The Performance and Microstructure of Green bodies on Gelcasting of Zirconium Ceramic;
凝胶注模成型氧化锆陶瓷坯体的性能和显微结构分析
3.
Effects of several factors on gelcasting of Alumina-(3:1)spinel slurries;
几种因素对刚玉-(3:1)尖晶石体系凝胶注模成型工艺的影响
4) gel-casting
凝胶注模成型
1.
Influence of MgO and TiO_2 on mechanical properties of zirconia toughened alumina ceramics formed by gel-casting technique
MgO和TiO_2烧结助剂对凝胶注模成型氧化锆增韧氧化铝陶瓷性能的影响
2.
The preparation processing of SiC/carbon black suspension with low viscosity and high solid loading for gel-casting was studied.
研究了碳化硅/炭黑凝胶注模成型中低粘度、高固含量浆料的制备工艺,分析讨论了碳化硅颗粒级配、分散剂、pH值以及有机单体含量对浆料流变性能的影响,成功地制备出固相体积分数为60%,表观粘度为680mPa。
3.
The green bodies of titanium-bioglass composite were prepared by gel-casting process.
采用凝胶注模成型工艺制备了钛-生物玻璃复合材料坯体。
5) gel casting
凝胶注模成型
1.
Technological factors in gel casting of Al_2O_3-SiC composite;
Al_2O_3-SiC复相陶瓷凝胶注模成型工艺因素的研究
2.
Nano-SiO_(2)-coated Al_(2)O_(3) micro-composite system was derived from silica sol and αAl_(2)O_(3) to prepare mullite ceramics by gel casting technology.
采用硅溶胶等制备纳米SiO2包覆Al2O3微复合体系,凝胶注模工艺制备莫来石陶瓷,着重研究了低粘度高固含量浓悬浮体系的特性及其凝胶注模成型坯体的性能。
3.
It was described that study on gel casting and sintering of silicon carbide in this paper.
研究了碳化硅耐火材料的凝胶注模成型及其烧结性状 。
6) Gel casting
凝胶注模
1.
The inhibition of oxygen,which occurred in gel casting during the formation of polymer networks through in-situ polymerization of monomers in air,was successfully prevented by adding a proper amount of polyethylene glycol(PEG) to the pre-aqueous acrylamide solution.
采用凝胶注模工艺制备Al2O3陶瓷过程中,在单体和交联剂的预混溶液中加入适量的聚乙二醇(PEG),能有效克服单体聚合的氧阻聚问题,从而消除陶瓷坯体的表面起皮现象。
2.
In this paper, process of the gel casting dosage of the organic material and the primary conditions control are interviewed, and advantages of the gel casting are enumerated.
系统地叙述了凝胶注模成型工艺的工艺过程、主要用料和工艺过程中一些关键条件的控制,对其工艺特点进行了说明,并在多方面与其它几种常用的成型方法进行比较;简单介绍了微波介质陶瓷的发展过程和成型工艺的研究现状;详细分析了凝胶注模成型工艺的成型原理和将其应用于微波介质陶瓷领域的优势,并对其应用前景进行了展望。
3.
The influence factors of gel casting ZTA green body are investigated.
通过测量含不同种类和质量分数粉末浆料的粘度,坯体的密度和线性收缩率,研究了用凝胶注模成型的ZTA陶瓷坯体的影响因素。
补充资料：Sds-聚丙烯酰胺凝胶电泳凝胶电泳
sds-聚丙烯酰胺凝胶电泳（sds-page，sodium dodecyl sulfate-polyacrylamide gel electrohoresis）
在有去污剂十二烷基硫酸钠存在下的聚丙烯酰胺凝胶电泳。sds-page只是按照分子大小分离的，而不是根据分子所带的电荷和大小分离的。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条