1) Crystalline rate
结晶效率
2) crystallization effect
结晶效应
1.
Corresponding to the interfacial properties of the fiber-reinforced polymer composites, the structure and action mechanism of interfacial layer were reviwed with the emphasis on the effects of interfacial crystallization effect on the mechanical properties of composites, including characterizations of interfacial properties.
针对纤维增强聚合物基复合材料的界面性能,系统阐述了其界面层的结构和作用机理,详细介绍了界面结晶效应对力学性能的影响及界面性能的表征方法,最后论述了几种有效的纤维表面改性方法及改性效果。
3) crystallization rate
结晶速率
1.
The results show that nonisotheramal crystallization results are successfully analyzed by Mo Zhishen theory,and the crystallization rate of mLLDPE is slo- wer than that of traditional LLDPE at the same relative crystallinity.
结果表明,采用莫志深法处理数据可得到较好的线性关系,且mLLDPE在相同的相对结晶度下的结晶速率低于LLDPE。
2.
A kind of PET/GF composite with good mechanical properties and rapid crystallization rate was prepared.
制备了结晶速率快、力学性能优异的玻纤增强聚对苯二甲酸乙二酯(PET/GF)。
3.
The crystallization rate and the relative crystallization degree of PP/Talc composites is higher than those of pure PP, which causes the change of growing way for crystal nucleus and is advantageous to the processing and properties for PP/Talc composites.
用差示扫描量热法(DSC)研究聚丙烯(PP)及PP/Talc复合材料的非等温结晶过程,加入滑石粉后,PP/Talc的结晶速率、结晶度得到明显提高。
4) rate of crystallization
结晶速率
1.
Based on the experimental results and theoretical calculation, the effects of nano silica on the crystallinity and rate of crystallization of PET were obtained.
以纳米氧化硅作PET填加剂 ,实验测定及理论计算得到不同填加量对PET的结晶度及结晶速率的影响 ,表明纳米氧化硅的适宜填加量为 1 6 4 %。
5) crystallinity
结晶率
1.
To control the quatity, grain size and morphology of crystals in glass ceramics, relative crystallinity of CaO Al 2O 3 SiO 2 sintered glass ceramics was determined using XRD method.
为控制微晶玻璃中晶体的数量、晶粒尺寸和形貌，采用Ｘ射线方法测定了ＣａＯ－Ａｌ２Ｏ３ －ＳｉＯ２ 系玻璃颗粒在烧结过程中的相对结晶率，并结合扫描电镜研究了不同温度区域内的结晶过程。
6) crystallization ratio
结晶化率
1.
The results showed that the crystallization ratio and time of mold fluxes had great difference at the different temperature.
结果表明:不同的实验温度条件下,连铸保护渣的结晶化率和结晶时间相差很大。
补充资料：配置效率和生产效率
在经济学上，经济发展的动力，或者说效率的来源，分为两类：一类是配置效率，二是生产效率。所谓配置效率，是指给定资源和技术的条件下，怎么样使资源从边际生产率低的地方流向边际生产率高的地方，从而使得资源和利用更合理、社会总价值达到最大;而生产效率是指如何通过技术进步提高每一种资源的生产率，也就是把社会的生产可行性边界向外移。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条