2) stainless steel bellows
不锈钢波纹管
1.
L-type bench valves installed upstream from hotplate are installed using stainless steel bellows in indoor gas project for residential consumers.
在居民用户室内燃气工程中采用不锈钢波纹管,安装L型灶前台式阀,通过波纹定尺管与灶具螺纹连接,解决了胶管脱落引发燃气泄漏的问题。
2.
The internal and external standards and codes for new pipe materials,including stainless steel bellows,copper tubing and polyethylene-aluminum-polyethylene composite pipe etc.
介绍了国内外标准、规范对不锈钢波纹管、铜管和铝塑复合管等新型管材在室内燃气管道中应用的规定。
3.
However, in practice, the main failure way of the stainless steel bellows is corrosion, especially stress corrosion, while fatigue or any other abnormal factors are not popular.
根据不锈钢波纹管在使用中的这一特点,本论文从波纹管的残余应力测定、金相分析和腐蚀试验三方面着手,找到引起奥氏体不锈钢波纹管应力腐蚀的致因;同时通过对固溶处理的研究,掌握了有效防止不锈钢波纹管应力腐蚀的方法。
3) stainless steel corrugated flexible pipe
不锈钢波纹软管
4) stainless steel plate
不锈钢板
1.
Discussion on the service life of rolling oil filter of cold mill for stainless steel plate;
不锈钢板冷轧机轧制油过滤器寿命探讨
2.
In this paper,the new welding procedure is introduced to weld plates with stainless steel plates instead of composite ones.
针对船舶钢结构工程修理中的复合板换新问题,文章提出以不锈钢板替代复合板进行焊接的焊接工艺,通过焊接工艺评定后进行现场焊接,焊接结果符合检验标准。
3.
Welding 3 mm thick stainless steel plate by using CO2 laser-TIG hybrid welding, the effects on welds width and penetration by welding parameters was studied based on multiple linear regression method.
采用CO2激光-TIG复合焊接3mm厚的不锈钢板,基于多元线性回归方法,研究了焊接工艺参数对焊缝熔宽及熔深的影响。
5) stainless steel
不锈钢板
1.
This paper describes the method and processing parameters of laser welding of 8 mm thick stainless steel with high power Nd∶YAG CW laser.
探讨了采用高功率Nd∶YAG连续激光器焊接 8mm厚不锈钢板的工艺方法及工艺参数。
2.
This thesis to the wiredrawing stainless steel plate curtain wall application principle,main point of design and the construction control carried on a brife narration.
本文对拉丝不锈钢板幕墙的应用原理,设计要点和施工控制进行了简要叙述,拉丝不锈钢板幕墙做为一种新的装饰材料和工艺,较强的耐腐蚀和强度性能,将得到更广泛的应用和发展。
6) stainless steel sheet
不锈钢板
1.
The influence of different laser-spot spaces on deformation results of SUS304 stainless steel sheet was studied,and simulated by Finited Element Soft-ABAQUS.
实验研究了不同的光斑间距对SUS304不锈钢板激光冲击的变形影响,并用ABAQUS软件进行了有限元仿真分析。
2.
The FEM simulation of spring-back of stainless steel sheet s cold-roll forming process is investigated using anisotropic yield functions(Hill,YLD 89),and comparing the results with the experiments data.
基于不锈钢板冷弯成型和回弹过程的数值模拟,研究了各向异性屈服准则Hill和YLD89对不锈钢板冷弯成型模拟的影响。
补充资料：板波纹填料
分子式：
CAS号：
性质：用板材制成的一种整装填料。其结构和几何形状与网波纹填料类似，只是用金属、塑料或陶瓷板取代了丝网。金属板波纹填料保持了网波纹填料压降低、通量高、持液量小、放大效应小等优点，其造价比网波纹填料低得多。
CAS号：
性质：用板材制成的一种整装填料。其结构和几何形状与网波纹填料类似，只是用金属、塑料或陶瓷板取代了丝网。金属板波纹填料保持了网波纹填料压降低、通量高、持液量小、放大效应小等优点，其造价比网波纹填料低得多。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条