1) Plasmon resonance light scattering (PRLS)
等离子体共振光散射
2) plasma
等离子体
1.
Combination of non-thermal plasma and heterogeneous catalysis for removal of low concentration benzene hydrocarbons in air;
非热等离子体与催化相结合去除气相低浓度苯系物
2.
Extraction and separation of intermediates in plasma degradation of benzene;
苯等离子体降解中间产物的萃取与分离
3.
Effects of energy injection on removal of benzene hydrocarbons in the air by discharge plasma;
能量注入对放电等离子体去除气相苯系物的影响
3) plasma
等离子
1.
High efficient plasma welding technology and its application;
高效等离子焊接技术及其应用
2.
Cavitation erosion characteristics of Ni60+TiC plasma cladding layer;
Ni60+TiC等离子熔覆层的汽蚀特征
3.
Exergy analysis of thermal plasma reactor for coal gasification;
煤等离子气化反应器的火用分析
4) plasma arc
等离子弧
1.
Effects of Ti-Mg on properties of plasma arc "in-situ" welding for SiCp/Al MMCs;
Ti-Mg对SiCp/Al复合材料等离子弧原位焊接性能的影响
2.
Usage and maintenance of welding and cutting machines(62)——Usage and maintenance of plasma arc cutting machine;
焊接与切割设备的使用和维修(六十二)——空气等离子弧切割机的使用与维修
3.
Strengthening planning for grooved surface with chromium-plating with plasma arc;
槽形表面镀铬层等离子弧强化工艺规划
5) plasma beam
等离子束
1.
Fe-based alloy design in surface metallurgy by plasma beam;
等离子束表面冶金铁基合金的设计与研究
2.
Effects of compress argon arc plasma beam scanning on microstructure and composition of electroless Ni-P alloy layer;
压缩氩弧等离子束扫描对化学镀Ni-P合金镀层组织与成分的影响
3.
In view of the wear out of diesel engine cylinder liners,the high energy density plasma beam was applied to high speed scanning the liner surface of cylinder under atmospheric pressure and to make improvement treatment on the in-wall of cylinder liner partly so as to obtain the high hardness at hardened layer.
针对柴油机气缸套磨损失效现象,采用高能等离子束在常压下快速扫描气缸套内表面,对其进行局部硬化改性处理,获得了高硬度淬火硬化层。
6) plasma torch
等离子炬
1.
On base of surface metallurgy by plasma beem, plasma torch has been improved to solve burning loss and solution of WC under high temperature.
在等离子表面冶金技术的基础上,针对金属陶瓷WC在高温下易烧损、熔解的特点,对现有设备的等离子炬进行改进,设计出表面冶金金属陶瓷专用等离子炬,将单送粉系统改为双送粉系统,并采用对比试验,对等离子炬改进前后形成的冶金层组织性能进行分析比较,结果表明,改进后的等离子炬所形成的表面冶金层中的WC烧损率大大减少,第二相强化效果明显,耐磨损性能大大提高。
2.
The design of plasma torch and the arc melting system are described in detail.
分析了CuCr触头材料等离子熔炼工艺的特点,详细介绍了等离子炬的设计和熔炼实验系统。
3.
The design of plasma torch, which is the center part of surface metallurgy equipment by plasma-jet, the selection of alloying powder and processing parameter are analysed in the paper.
系统地分析和探讨了等离子束表面冶金设备的核心部件等离子炬的设计、表面冶金的合金材料的选择、表面冶金工艺的确定。
参考词条
补充资料：电感耦合等离子体光量计
一种以等离子体光源作为激发源的多元素光谱分析仪(见图)。等离子体光源有直流等离子光源，电感耦合等离子体光源，电容耦合等离子体光源。仪器由等离子发生器、雾化室、炬管、分光计、光电检测系统组成。操作程序，背景校正，数据处理和打印结果都由计算机控制。其工作原理是:由高频发生器（一般为27.12兆赫）提供的高频能量叠加到炬管外面的线圈上，线圈内通水冷却，立于线圈当中的同轴型三层石英管，分别通入不同量的氩气，称为冷却气流，辅助气流和进样气流。点火后炬管端就出现一个氩等离子体焰，最高温度达10000K。试样在高温下被激发而辐射出光, 经分光计按一定波长次序分散, 取得一系列线光谱，通过焦平面上安装的出射狭缝，由光电检测系统接收，将光谱强度与标准相比较，转换为元素的含量。其优点是：分析速度快，干扰少，能同时测定几十种元素，精密度好，测定下限低（一般为μg/m1或更低），线性范围宽等特点。在地质学中用于测定岩石、矿石、矿物和地下水中常量、微量、痕量的金属元素。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。