1) analytic units
分析单元
1.
The population analytic units with different scales should reflect the differences of population distribution and the population data accuracy in these units shou.
不同尺度下的分析单元大小应能反映出人口的分布差异，人口数据精度能满足研究目的的需要。
2) unit analysis
单元分析
1.
Evaluation of non-point source pollution based on unit analysis;
基于单元分析的非点源污染调查评估方法
2.
Aimed at the specific characteristics of agricultural non-point source pollution being difficult to monitor and control in irrigation areas,and based on the viewpoint of unit analysis,a concept of load contribution rate was put forward.
针对灌区农业非点源污染难以监测控制的具体特点,基于单元分析的观点,提出了负荷贡献率的概念,并在此基础上,建立了灌区农业非点源污染负荷估算方法;以青铜峡灌区为例,利用2005—2006年灌溉周期灌排水质监测试验资料对灌区年农业非点源污染矿化度、铵氮、总氮和总磷负荷进行了估算,并与平均浓度法进行比较。
3) regression analysis of single unit
单元回归分析
4) unit element analysis
单元要素分析
5) finite element analysis
有限单元分析
1.
This paper presents acoustic modal finite element analysis of the automobile passenger compartment to illustrate the implementation of the method in the design stage.
讨论轿车乘坐室声学模态的有限单元分析方法 ,说明该方法在轿车设计中的实现 。
6) analysis of element rigidity
单元刚度分析
补充资料：ANSYS壳单元分析箱梁
! Analysis a box beam section with shell elements of ANSYS
! 用ansys的壳体单元分析箱梁
! Box dimension: 10*4*4m with shell thickness of 0.04m
! By Lu Xinzheng, Depart. Civil Engineering, Tsinghua University, Beijing
! 陆新征，清华大学土木系
! Aug. 2004
! Define the Element
! 定义单元
/PREP7
!*
ET,1,SHELL93
!*
! Define the section for shells
! 定义壳单元截面
R,1,.04, , , , , ,
!*
! Define the material
! 定义材料
MPTEMP,,,,,,,,
MPTEMP,1,0
MPDATA,EX,1,,200e9
MPDATA,PRXY,1,,.3
! Setup the model
! 建模
! Define the keypoints
! 定义关键点
k,1,0,0,0
k,2,4,0,0
k,3,4,4,0
k,4,0,4,0
! Define the lines
! 定义线
l,1,2
l,2,3
l,3,4
l,4,1
! Define the section area
! 定义截面
a,1,2,3,4
! 用ansys的壳体单元分析箱梁
! Box dimension: 10*4*4m with shell thickness of 0.04m
! By Lu Xinzheng, Depart. Civil Engineering, Tsinghua University, Beijing
! 陆新征，清华大学土木系
! Aug. 2004
! Define the Element
! 定义单元
/PREP7
!*
ET,1,SHELL93
!*
! Define the section for shells
! 定义壳单元截面
R,1,.04, , , , , ,
!*
! Define the material
! 定义材料
MPTEMP,,,,,,,,
MPTEMP,1,0
MPDATA,EX,1,,200e9
MPDATA,PRXY,1,,.3
! Setup the model
! 建模
! Define the keypoints
! 定义关键点
k,1,0,0,0
k,2,4,0,0
k,3,4,4,0
k,4,0,4,0
! Define the lines
! 定义线
l,1,2
l,2,3
l,3,4
l,4,1
! Define the section area
! 定义截面
a,1,2,3,4
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条